Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
7. Racks and stands Only use a rack or stand that is recommended for use with audio equipment. If the equipment is on a portable rack it should be moved with great care, to avoid overturning the combination. 8. Cleaning Unplug the unit from the mains supply before cleaning. The case should normally only require a wipe with a soft, damp, lint-free cloth. Do not use paint thinners or other chemical solvents for cleaning. We do not advise the use of furniture cleaning sprays or polishes as they can cause indelible white marks if the unit is subsequently wiped with a damp cloth. 9. Power sources Only connect the appliance to a power supply of the type described in the operating instructions or as marked on the appliance. 10. Power-cord protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, and the point where they exit from the appliance. 11. Grounding Ensure that the grounding means of the appliance is not defeated. 12. Power lines Locate any outdoor antenna/aerial away from power lines. 13. Non-use periods If the unit has a stand-by function, a small amount of current will continue to flow into the equipment in this mode. Unplug the power cord of the appliance from the outlet if left unused for a long period of time. 14. Abnormal smell If an abnormal smell or smoke is detected from the appliance, turn the power off immediately and unplug the unit from the wall outlet. Contact your dealer immediately. 15. Servicing You should not attempt to service the appliance beyond that described in this handbook. All other servicing should be referred to qualified service personnel. 16. Damage requiring service The appliance should be serviced by qualified service personnel when: A. the power-supply cord or the plug has been damaged, or B. objects have fallen, or liquid has spilled into the appliance, or C. the appliance has been exposed to rain, or D. the appliance does not appear to operate normally or exhibits a marked change in performance, or E. the appliance has been dropped or the enclosure damaged. Safety compliance This product has been designed to meet the IEC 60065 international electrical safety standard. Using this handbook This handbook has been designed to give you all the information you need to install, connect, set up and use the Arcam CD36 compact disc player. The CR-314 remote control handset supplied with this equipment is also described. Safety Safety guidelines are set out on the inside front cover of this handbook. Many of these items are common sense precautions, but for your own safety, and to ensure that you do not damage the unit, we strongly recommend that you read them. Digital to Analogue conversion The CD36 incorporates the latest audio up-sampling technology to convert the 44.1kHz data from the CD up to 192kHz in 24-bit precision using the Analog Devices AD1896 sample rate converter. The 192kHz audio data is converted into the analogue domain using four Wolfson Micro WM8740 24-bit stereo DACs. Left and right output channels are made using two stereo DAC chips per channel, both operating in dual mono configuration per channel. The resulting four mono signals (two for each channel) are summed together to help improve dynamic range, linearity and therefore distortion. Due to the higher sample rates, the digital filters roll off less aggressively than for standard DACs, and the analogue filters have a wider bandwidth resulting in less phase distortion, particularly for the higher frequencies. Contents Safety guidelinesE-2 Important safety instructionsE-2 Safety complianceE-2 Using this handbookE-3 SafetyE-3 Digital to Analogue conversionE-3 InstallationE-4 Positioning the unitE-4 Connecting to other equipmentE-4 Connecting to a power supplyE-4 Using your CD playerE-5 CDs with textE-5 Using the CR-314 remote controlE-6 Remote-control codesE-7 Technical specificationE-8 GuaranteeE-9 Worldwide GuaranteeE-9 On line registrationE-9 Remote-control codes The following table gives the IR-commands accepted by the CD36. Items shown in italics reference the buttons on the supplied CR-314 remote control. The items not in italics are additional commands accepted by the CD36. Power commands Command Decimal Code Power toggle 20–12 Power-on 20–123 Power-off 20–124 Playback control commands Command Decimal Code Track number ‘n’, (e.g., 1) 20–n (e.g., 20–1) Track selection 10+ 20–10 Time 20–66 Remain 20–11 Track forward 20–32 Track back 20–33 Fast forward 20–52 Fast rewind 20–50 Open 20–45 Pause 20–48 Stop 20–54 Play 20–53 Advanced control commands Command Decimal Code Repeat toggle 20–29 Repeat off 20–125 Repeat one 20–126 Repeat all 20–127 Repeat A-B 20–59 Search 20–76 Scan 20–43 Scan 10 seconds 20–79 Scan 20 seconds 20–88 Scan 30 seconds 20–90 Scan off 20–90 Clear 20–58 Clear all 20–57 Programme 20–41 Programme on 20–99 Programme off 20–100 PMode (Shuffle) 20–64 Shuffle 20–28 S...