Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
other rights of third parties are not infringed. • For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not yet been broken. This deck is not suited for recording on CHROME (IEC II) or METAL (IEC IV) type cassettes. • The best recording level is set automatically. Altering the VOLUME or DBB controls will not affect the recording. • To protect a tape from accidental erasure, break out the tabs. If you wish to record again, cover the tabs with a piece of adhesive tape. CD Synchro Start Recording 1. Adjust the POWER slider to CD. 2. Insert a CD and if desired, program track numbers. 3. Insert a suitable tape into the cassette deck and close the door. 4. Press RECORD 0 to start recording. – Playing of the CD program starts automatically from the beginning of the program. You don't need to start the CD player separately. . To select and record a particular passage within a CD track: • Press SEARCH °or ¤. Release the control when you recognize the passage you want. • To pause CD playback, press 2;. • Recording starts from this exact point in the track when you press RECORD 0. 5. To pause recording, press PAUSE ;. Press PAUSE ; again to resume recording. 6. To stop recording, press STOP 9. Recording from the Radio 1. Tune to the desired radio station (see Tuning to radio stations). 2. Follow steps 3-6, under CD Synchro Start Recording. DIGITAL TUNER CD PLAYER CD PLAYER CASSETTE RECORDER SAFETY & MAINTENANCE INFORMATION (See 8) • Don't expose the set, batteries, CDs or cassettes to humidity, rain, sand or excessive heat. • Clean the set with a dry cloth. Don't use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the set. • Place the set on a hard and flat surface so that the system does not tilt. Make sure there is good ventilation to prevent the set overheating. • The mechanical parts of the set contain selflubricating bearings and must not be oiled or lubricated. CD player and CD handling • If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. • The lens of the CD player should never be touched! • Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. • Always close the CD-tape door to avoid dust on the lens. • To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. • Never write on a CD or attach any stickers to it. Tape deck maintenance To ensure quality recording and playback of the tape deck, clean parts A, B and Cas shown, once a month. Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid to clean the deck. 1. Open the CD-tape door. 2. Press PLAY 2 and clean the roller C. 3. Press PAUSE ; and clean the heads A, and the capstan B. 4. After cleaning, press STOP 9. No sound /power – Volume not adjusted • Adjust the VOLUME – Mains lead not securely connected • Connect the AC mains lead properly – Batteries exhausted/ incorrectly inserted • Insert (fresh) batteries correctly – Headphones connected to the set • Disconnect headphones Severe radio hum or noise – Electrical interference: set too close to TV, VCR or computer • Move the set to increase the distance Poor radio reception – Weak radio signal • FM: Adjust the FM telescopic aerial noPr indication – During programming radio preset stations, you have keyed in a preset number that exceeds the maximum preset number i.e. 40 • Key in a preset number from 1-40 noCd indication – CD badly scratched or dirty • Replace/ clean CD, see Maintenance – Laser lens steamed up • Wait until lens has cleared nFCd indication – CD-R(W) is blank/ not finalized • Use a finalized CD-R(W) dAtA indication – CD contains non-audio files • Press SEARCH °or ¤once or more to skip to a CD audio track, instead of the data file The CD skips tracks – CD damaged or dirty • Replace or clean CD – SHUFFLE or PROGRAM is active • Switch off SHUFFLE / PROGRAM Poor cassette sound quality – Dust and dirt on the heads, etc. • Clean deck parts, see Maintenance – Use of incompatible cassette types (METAL or CHROME) • Only use NORMAL (IEC I) for recording Recording does not work – Cassette tab(s) may be broken • Apply adhesive tape over the missing tab space Remote control does not function properly (for AZ1505 model only) – Batteries exhausted/ incorrectly inserted • Insert (fresh) batteries correctly – Distance/ angle between the set too large • Reduce the distance/ angle SAFETY & MAINTENANCE INFORMATION TROUBLESHOOTING Environmental information We have done our best to reduce the packaging and make it easy to separate into 3 materials: cardboard, expandable polystyrene, polyethylene. Your set consists of materials which can be recycled if disassembled by a specialize...