Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON (5) causes the operation to change from play to pause or from pause back to play. See the CUE INSTRUCTIONS section for more information. TRACK SKIP: The TRACK SKIP BUTTONS (6) let you select the track to play. SEARCH JOG WHEEL: The SEARCH JOG WHEEL (7) is used to accurately position the disc at the point where you wish the track to start playing. This position on the track will be memorized as the CUE POINT. Each move of the SEARCH JOG WHEEL (7), in PAUSE MODE, will move the memorized CUE POINT. See the CUE INSTRUCTIONS section for more information. SCAN DIAL: Use the SCAN DIAL (8) to select the scanning direction and speed. Turning the dial in the clockwise direction will scan forward and counterclockwise will scan in reverse. The scanning speed increases as the dial is turned further. STOP: The STOP BUTTON (9) will end the playing of the CD. Pressing the STOP BUTTON (9) will also clear the cues. TIME: The TIME BUTTON (10) switches the time display between the 3 different time displays (real time, track time remaining and total track time remaining). CUE 1 and CUE 2: Use the CUE BUTTONS (11) in setting cue points. See the CUE INSTRUCTIONS section for more information. In play mode, pressing a CUE BUTTON will pause play and bring you to the CUE POINT when you can then press the play/pause button to play from the CUE POINT. In play mode, holding down the CUE BUTTONS (11) for more than 3 seconds clears the cue. 4%, 8% and 16% BUTTONS: Use the 4%, 8% and 16% BUTTONS (12) to assign the percent the pitch control slide will have. The 4% button will assign +/-4% to the pitch control slide. The 8% button will assign Page 2 +/-8% to the pitch control slide. The 16% button will assign +/-16% to the pitch control slide. The PITCH CONTROL (13) must be ON for the 4%, 8% and 16% BUTTONS (12) to work. PITCH: Pushing the PITCH CONTROL (13) activates the pitch section of the unit (pitch LED glows red). The pitch of the CD will change according to the position of the PITCH CONTROL (13). PITCH BEND BUTTONS: Pushing the PITCH BEND BUTTONS (14) will automatically raise or lower the pitch +/-4%, 8% and 16% without changing the slide setting. Releasing the buttons will return the pitch to the slide setting. You can use this function to match the pitch bend when mixing from one song to another. SET CUE: Use the SET CUE (15) button to activate the DIRECT ACCESS BUTTONS to set a CUE POINT. See the CUE INSTRUCTIONS section for more information. DIRECT ACCESS BUTTONS: Use the DIRECT ACCESS BUTTONS (16) to select what track to play and to set a CUE POINT. See the CUE INSTRUCTIONS section for more information. SINGLE: Pressing the SINGLE (17) button will activate the AUTO CUE FUNCTION and cause the unit to stop at the beginning of music of the following track. This allows you to start play immediately from the start of music without any blank space (which exists at the beginning of every track). CONTINUE: The CONTINUE (18) function will cause the unit to play continuously. PLAYBACK DISPLAY: The PLAYBACK DISPLAY (19) displays the time remaining to play and flashes slowly when the track has 15 seconds left. The PLAYBACK DISPLAY (19) flashes quickly when the track has 5 seconds left. DIGITAL OUTPUT JACK: Connecting any type of DAT, MD, HARD DRIVE, or other such items which accept digital signals into the BNC CONNECTOR (24) on the rear panel of the transports allows you to receive a digital signal from CD. CUE INSTRUCTIONS Special Mode for CUE 1 (only): 1. Play the track you wish to play, push pause and move the SEARCH JOG WHEEL (7) to the exact point you wish play to begin, and then PLAY/PAUSE BUTTON (5) to memorize the CUE 1 POINT (CUE 1 LED will blink). NOTE: When a CUE LED is not lit, there is no CUE POINT saved in memory. When a CUE LED is blinking, the unit is ready for you to change the CUE POINT. When a CUE LED stays lit, there is a CUE POINT saved in memory. To change the saved CUE POINT you have to press this CUE BUTTON (the CUE LED will then blink) and then you can change the CUE POINT. To set a cue point, follow these instructions: 1. Use the TRACK SKIP (6) to find the track you wish to play. Listen to the track and when the track gets to the approximate spot, push the PLAY/PAUSE BUTTON (5), and if the cue LED is not blinking (indicating the unit is ready for you to set the cue) press the CUE BUTTON you wish to assign the cue to (CUE 1 or CUE 2), than you must touch the SEARCH JOG WHEEL (7) to fine tune the memorized cue point, adjusting the CUE POINT forward or backward. The unit will go into CUE MODE (cue LED will be lit) and the location indicated on the display will be the memorized cue point. Push the PLAY/PAUSE BUTTON (5), and the unit will instantly play from the spot selected. If you don’t want to memorize the adjusted CUE POINT, after touching the SEARCH JOG WHEEL (7), push the CUE BUTTON (with the blinking LED) and then the PLAY/PAUSE BUTTON (5). While in play mode, press...