Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
In play mode, pressing a CUE BUTTON will pause play and bring you to the CUE POINT when you can then press the play/pause button to play from the CUE POINT. SET CUE: Use the SET CUE (10) button to activate the DIRECT ACCESS BUTTONS to set a CUE POINT. See the CUE INSTRUCTIONS section for more information. DIRECT ACCESS BUTTONS: Use the DIRECT ACCESS BUTTONS (2) to select what track to play and to set a CUE POINT. See the CUE INSTRUCTIONS section for more information. SINGLE-AUTO CUE/CONTINUOUS: Pressing the SINGLE-AUTO CUE/ CONTINUOUS (11) button activates the AUTO CUE FUNCTION. The AUTO CUE FUNCTION causes the unit to pause at the beginning of music of the following track and allows you to start play immediately from the start of music without any blank space (which exists at the beginning of every track). Pressing the SINGLE-AUTO CUE/CONTINUOUS (11) button a second time activates the CONTINUOUS function causing the unit to play continuously (after the last track, the unit will return to the first track of the disc and continue to play). Pressing the SINGLE-AUTO CUE/CONTINUOUS (11) button a third time deactivates the CONTINUOUS function. ROBO START: Press the ROBO START (1) button to activate ROBO START (the button will blink). Use ROBO START in SINGLE-AUTO CUE MODE to alternate play between the two sides of the CD player (one track from one side, then one track from the other side). See the “Robo Start Instructions” section for further instructions. PITCH CONTROL: Pushing the PITCH CONTROL (5) activates the pitch section of the unit (pitch LED glows red). The pitch of the CD will change according to the position of the PITCH SLIDE (16). PITCH BEND BUTTONS : Pushing the PITCH BEND BUTTONS (6) will automatically raise or lower the pitch +/- 16% without changing the slide setting. Releasing the buttons will return the pitch to the slide setting. You can use this function to match the pitch bend when mixing from one song to another. Page 4 DIGITAL OUTPUT JACK: Connecting any type of DAT, MD, HARD DRIVE, or other such items which accept digital signals to the BNC OUTPUT CONNECTOR (24) on the rear panel of the transports allows you to record a digital signal from CD. OPERATING INSTRUCTIONS 1. Make sure that the VOLTAGE SELECTOR SLIDE (22) switch, found on the rear panel, is set for the proper voltage. Plug the unit in and press the POWER SWITCH (20). The unit will turn on. Pushing the POWER (20) switch a second time will turn the unit off. 2. Press the OPEN/CLOSE BUTTON (7), place a CD in the DISC TRAY (19) and press the OPEN/CLOSE BUTTON (7) again. The tray will close into the unit. 3. Push the TRACK SKIP BUTTONS (15) to select the track you want to play. 4. Press the PLAY/PAUSE BUTTON (17) and the unit will instantly play. CUE INSTRUCTIONS Special Mode for CUE 1 (only): 1. Play the track you wish to play, push pause and move the SEARCH JOG WHEEL (9) to the exact point you wish play to begin, and then PLAY/ PAUSE (17) button to memorize the CUE 1 POINT (CUE 1 LED will blink). NOTE: When a CUE LED is not lit, there is no CUE POINT saved in memory. When a CUE LED is blinking, the unit is ready for you to change the CUE POINT. When a CUE LED stays lit, there is a CUE POINT saved in memory. To change the saved CUE POINT you have to press this CUE BUTTON (the CUE LED will then blink) and then you can change the CUE POINT. To set a cue point, follow these instructions: 1. Use the TRACK SKIP (15) to find the track you wish to play. Listen to the track and when the track gets to the approximate spot, push the PLAY/PAUSE (17) button, and if the cue LED is not blinking (indicating the unit is ready for you to set the cue) press the CUE BUTTON you wish to assign the cue to (CUE 1 or CUE 2), than you must touch the SEARCH JOG WHEEL (9) to fine tune the memorized cue point, adjusting the CUE POINT forward or backward. The unit will go into CUE MODE (cue LED will be lit) and the location indicated on the display will be the memorized cue point. Push the PLAY/PAUSE (17) button, and the unit will instantly play from the spot selected. If you don’t want to memorize the adjusted CUE POINT, after touching the SEARCH JOG WHEEL (9), push the CUE BUTTON (with the blinking LED) and then the PLAY/PAUSE (17) button. While in play mode, pressing the CUE BUTTON will pause the play and bring you back to the CUE POINT. 2. Press the second CUE BUTTON from PLAY MODE ONLY and repeat the process with the second CUE BUTTON, to set a second CUE POINT. 3. To preview a CUE POINT, from PLAY MODE press PLAY/PAUSE (17) button, and then press and hold down the CUE BUTTON to preview the CUE. Letting go of the CUE BUTTON will bring you back to the CUE POINT and PAUSE MODE. AND/OR To use the SET CUE BUTTON (15) and the DIRECT ACCESS BUTTONS (2) to set a cue point, follow these instructions: 1. Press the SET CUE BUTTON (15) (the LED will light). Use the DIRECT ACCESS BUTTONS (2) to memorize the spot at which you want play to start, the CUE POINT, by sele...