Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Pressing the SINGLE (15) button a third time deactivates the CONTINUOUS function. TIME: The TIME (16) button switches the time display between the three available choices listed under DISPLAY. LOOP IN: Pressing the LOOP IN (17) button while a track is playing will set a loop point. LOOP OUT: After a loop point is memorized, pressing LOOP OUT (18) in play mode will repeat the section between the first loop point and a second loop point when the LOOP OUT (18) button was pressed. Press LOOP OUT (18) again or pause play to exit the repeating play. RELOOP: Press for repeated loop play (stutter) from the first loop point or to reloop a previously set loop. The RELOOP (19) function automatically returns the music to the loop point and will play the loop until it is released with the LOOP OUT (18) button. CD starts instant play from the previously set cue points. PITCH SELECT: Pressing the PITCH SELECT (20) buttons enable you to select pitch levels ranging from 4%, 8%, & 16%. Press the two buttons labeled PITCH OFF together to turn OFF the pitch control. C4) PITCH BEND BUTTONS: Pushing the PITCH BEND BUTTONS (21) will automatically raise the pitch up to +4% or lower the pitch down to -4% from the existing pitch setting. Releasing the buttons will return the pitch to the original pitch setting. You can use this function to match the pitch bend when mixing from one song to another. PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE (22) up or down will lower or raise the pitch percentage. OPERATING INSTRUCTIONS: 1. Press the EJECT (7) button, place a CD in the DISC TRAY (6) and close the tray door. The display will initially show the number of tracks and the total time of the CD. 2. Push the TRACK SKIP (13) buttons to select the track you want to play. 3. Press the PLAY/PAUSE (8) button and the unit will instantly play. CUE INSTRUCTIONS: 1. To start the play at a point other than the beginning of a track, follow these instructions: First choose the track you wish to play, and then press PLAY/PAUSE (8) so the unit goes into the play mode. Press PLAY/PAUSE (8) to pause play at the spot where you want the play to start the CUE POINT. Use the SEARCH BUTTONS (14) to pick the precise spot you want play to begin, then press PLAY/PAUSE (8) again to save the cue point. Press the CUE (10) button to pause play at the cue point (the unit will go into the pause mode and the location indicated on the display will be the memorized cue point). You can preview the cue point by pressing and holding down CUE (10). Press PLAY/PAUSE (8) to begin play from the cue point. TROUBLESHOOTING: • If the disk will not play, check to see if the disc was loaded correctly (label side up). Also check the disc for excessive dirt, scratches, etc. • If the disc turns but there is no sound, check the cable connections. If they are okay, check your amplifier or receiver. • If the CD skips, check the CD for dirt or scratches. Do not assume that the CD player is defective. Many CDs are recorded out of spec and will skip on most or all CD players. Before sending the unit in for repair, try playing a CD that you are sure plays properly. SPECIFICATIONS: GENERAL: Disc Type................................Standard Compact discs (12 cm & 8 cm) Time Display.....................Track Elapsed, Track Remain, or Total remain Variable Pitch......................................± 16% Slider with Resume Switch Start...........................................................................Within 0.03 seconds Track Selection..................................................................... 1 to 99 Tracks AUDIO SECTION: Quantization......................................1 Bit Linear/Channel, 3 Beam Laser Oversampling Rate.......................................................................... 8 Times Sampling Frequency.....................................................................44.1 kHz Frequency Response......................................................20 Hz to 20 kHz Total Harmonic Distortion..............................................Less Than 0.005% Signal to Noise Ratio.....................................................................>96 dB Dynamic Range.................................................................................>94 dB Output Level (nominal)........................................................1.9 Volts R.M.S. Power Supply.......................................................AC 120/230V, 60/50 Hz Dimensions...............................8.5” x 3.75” x 12.5” (216 x 95.25 x 317 mm) Weight..................................................................................4.5 lbs. (2 kg) 2. Once you have saved a cue point you can fine tune or change the SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE memorized cue point: WITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT. To change a cue point, push PLAY/PAUSE (8) so the unit plays from the cue point, then press PLAY/PAUSE (8) at the spot you wi...