Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
i Search Buttons: Press one of these buttons to search forward N or backwards a through a disc to locate a particular portion of the selection being played. j Play Button: Press this button to start the playback of a CD. If the CD drawer is open, pressing this button will automatically close the drawer. k Stop: Press this button to stop the disc currently being played. l Pause Button: Press this button once to momentarily stop a disc. When the button is pressed again, the disc will resume play at the point it was stopped. m Random Button: Press this button to put a disc into play, and to have all of the tracks played in a random order. (See page 10 for more information.) nTime Button: Press this button to select the time display. In normal operation, the display will show the running time of a track being played. Press the button once to check the time remaining for the track in play. Press the button a third time to view the total play time remaining for the disc in play. o Check Button: Press this button to check the order of tracks programmed into the HD720’s memory. (See page 13 for complete information on programming the HD720.) p Intro Button: Press this button to put the HD720 in the Intro Scan mode. When you press the button, the unit will play the first 15 seconds of each track on the disc, and then move to the next track. Press the button again to defeat the function and continue full play of the current track. (See page 12 for more information.) q Display Button: Press this button once to dim the front panel display to half brightness. Press it again to turn the display lights off completely. Another press will return the display to normal brightness. Installation 9 To prevent possible damage to your speakers and other components in your audio system, it is important that ALL components, including the HD720 and receivers are turned off and unplugged from their AC power source when installing any new component. Connecting the HD720 to your audio system is simple. Using standard RCAto- RCA interconnect cords, connect the left and right Fixed Audio Output jacks . on the rear panel to the CD input jacks on your receiver, surround processor or preamplifier. If your system includes an optional, external digital-to-analog converter, or if you are using a receiver or other processor that has the capability to decode PCM digital input signals, connect the Coaxial Digital Output jack A to the Datastream Digital input on the decoder. Make certain to use a coaxial- style interconnect cable, as standard audio cables will not perform as well. Install the two AA batteries supplied with the HD720’s remote by turning the remote over so that you are holding the bottom side up. Press lightly on the embossed arrow on the cover, and gently slide the cover towards you in the direction of the arrow. Insert the batteries inside the compartment, being careful to follow the + and – polarity indications at the bottom of the compartment. Replace the cover by placing it on the remote and sliding it back towards the top of the remote. NOTE: When replacing batteries it is always a good idea to replace both at the same time. When the unit will not be used for an extended period of time, it is also a good idea to remove the batteries so that the potential for corrosion or damage is avoided. Connect the power to a non-switched AC wall outlet, or to the accessory outlet on the rear of another audio device in your system and you are ready to go! NOTE: When using the accessory outlet on another product to power the HD720 make certain that it has the ability to power a device that draws at least 14 watts of current in addition to the requirements of other devices that may be plugged into the accessory outlets. If you use a “switched” outlet, it is important to remember that the host product must be turned on in order for the HD720 to operate. Operation 10 Normal Play To play a disc, first turn the HD720 on using the Main Power Switch 1. If the unit has previously been turned on with the Main Power Switch, but then turned off using the remote control, the Status Mode Indicator 2will glow amber. In that case, the HD720 may be turned on using the Power On button bon the remote control. To load a disc, first press the Open/Close button &, taking care to make certain that the space in front of the drawer is not obstructed. Note that if the drawer is blocked when attempting to open it, it will automatically close within five seconds to protect the mechanism. Load the disc in the tray with the printed (label) side facing up. Make certain that the disc is centered in the tray. Either 5" or 3" discs may be used. When a 3" disc is played, it should be carefully centered within the smaller ridges inside the cassette drawer. Labeled Surface To retract the drawer back into the player after loading a disc, press the Open/Close button &. After a brief pause, the Information Display will show the total number of tracks on a disc and the total runnin...
мало с ним жил, но пока что нравится