Оценок - 4, средний балл: 4
(
)
)
|
Фото и характеристики Alpine CDA-7876RB |
Фрагмент инструкции
The back of the movable display will get very warm under normal operating conditions. This is not a malfunction. Do not touch. 6-EN Basic Adjusting Volume/Balance (Between Left and Right)/Fader (Between Front and Rear) 1 Press the MODE (Audio Control) knob repeatedly to choose the desired mode. Each press changes the modes as follows: > BAL > FAD > VOL NOTES • If the MODE (Audio Control) knob is not rotated within 5 seconds after selecting the BALANCE, or FADER mode, the unit automatically returns to the VOLUME mode. • When the subwoofer or BBE mode is ON, their respective levels may be adjusted. 2 Rotate the MODE (Audio Control) knob until the desired sound is obtained in each mode. NOTE When the temperature inside the unit rises, the volume may decrease momentarily. This is not a malfunction. Selecting BBE Mode The BBE (Barcus Berry Electronics) processor installed in this unit is designed to correct the phase distortion inherent in most loudspeaker designs. Ensuring the phase integrity of the signal driving the speakers improves the accurate reproduction of the sound. 1 Press and hold the BBE button for at least 2 seconds to turn on and off the BBE mode. 2 In BBE mode, press the MODE (Audio Control) knob to select the BBE adjusting mode. Each press changes the adjusting mode. 3 To change to a desired BBE level, rotate the MODE (Audio Control) knob. The BBE level can be changed from +1 to +3. NOTE The initial mode is +2. Adjusting Source Signal Level If the difference in volume level between the CD player and FM radio is too great, adjust the FM signal level as follows. 1 Press and hold the SETUP button for at least 3 seconds. 2 Press the f UP button repeatedly to select "FM-LV." Each press of the f UP button scrolls the modes as follows: > FM-LV > REG > PTY31 > HI-FI/NORMAL/STABLE > AMBER. DEMO < AUX < SCR < MUTE < BEEP < SUB < DIM < . CDA-7873R/TDA-7587R Only NOTE When you press the g DN button, the display scrolls in the reverse sequence. 3 Press the TUNE button to select the FM signal level mode. Each press toggles between "FM-LV HI" (High) and "FM-LV LO" (Low). 4 Press the SETUP button to activate the normal mode. Changing Backlighting Colour CDA-7873R/TDA-7587R only 1 Press and hold the SETUP button for at least 3 seconds. 2 Press the f UP button repeatedly to select "AMBER". Each press of the f UP button changes the modes as shown: NOTE If you press the g DN button the display scrolls in reverse sequence. > FM-LV > REG > PTY31 > HI-FI/NORMAL/STABLE > AMBER. DEMO < AUX < SCR < MUTE < BEEP < SUB < DIM < . CDA-7873R/TDA-7587R Only 3 Press the TUNE button to toggle the mode between "AMBER ON" (amber) and "AMBER OFF" (green). 4 Press the SETUP button to set the selected mode. 7-EN Basic TUNE MODE g DN f UP SETUP Basic Operation Dimmer Control Subwoofer On and Off Set the DIMMER control to AUTO to decrease the illumination brightness of the unit with the head lights of the vehicle ON. This mode is useful if you feel the unit's backlighting is too bright at night. 1 Press and hold the SETUP button for at least 3 seconds. 2 Press the f UP button repeatedly to select "DIM." Each press of the f UP button scrolls the modes as shown: > FM-LV > REG > PTY31 > HI-FI/NORMAL/STABLE > AMBER. DEMO < AUX < SCR < MUTE < BEEP < SUB < DIM < . CDA-7873R/TDA-7587R Only NOTE If you press the g DN button the display scrolls in reverse sequence. 3 Press the TUNE button to select the Dimmer mode. Each press toggles between "DIM AUTO" and "DIM MANU." 4 Press the SETUP button to activate the normal mode. 1 Press and hold the SETUP button for at least 3 seconds. 2 Press the f UP button repeatedly to select "SUB (Subwoofer)." Each press of the f UP button changes the modes as shown: > FM-LV > REG > PTY31 > HI-FI/NORMAL/STABLE > AMBER. DEMO < AUX < SCR < MUTE < BEEP < SUB < DIM < . CDA-7873R/TDA-7587R Only NOTE If you press the g DN button the display scrolls in reverse sequence. 3 Press the TUNE button to toggle mode between "SUB-W ON" and "SUBW OFF." 4 Press the SETUP button after setting the SUB-W ON. 5 Press the MODE (Audio Control) knob repeatedly to select the SUB-W mode. > SUB-W > BAL VOL < FAD < If an Ai-NET compatible processor with Subwoofer output is connected: The subwoofer output phase is toggled SUBW NOR (0°) or SUBW REV (180°) by pressing the g DN button or the f UP button. 6 Rotate MODE (Audio Control) knob until the desired sound is obtained in each mode. 8-EN Basic Sound (Beep) Guide Function This function will give audible feedback with varying tones depending upon the button pressed. 1 Press and hold the SETUP button for at least 3 seconds. 2 Press the f UP button repeatedly to select "BEEP." Each press of the f UP button changes the modes as shown: NOTE If you press the g DN button the display scrolls in reverse sequence. > FM-LV > REG > PTY31 > HI-FI/NORMAL/STABLE > AMBER. DEMO < AUX < SCR < MUTE < BEEP < SUB < DIM < . CDA-7873R/TDA-7587R Only 3 Press the TUNE button to toggle the mode between "BEEP ON" and "B...
Эта инструкция также подходит к моделям:CD-проигрыватели - CDA-7873R (455.16 kb)