Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Note: Memory cues are erased automatically when a new CD is played, or by holding memory button down for 5 seconds. (g) JOG WHEEL PITCH BEND: During normal playback, the inner jog wheel acts as a momentary pitch bend. Turing the wheel in a clockwise direction will increase the speed and turning the wheel in a counter-clockwise direction will decrease the speed. (h) SCRATCH BOX COMPATIBLE: This feature is used in conjunction with the optional American Audio® Scratch Box.™ mixers that also feature “Fader Q Start” control. When the DCD-PRO600 is used in conjunction with the Scratch Box a turntable may be used to control the CD functions. See Optional Scratch Box on page 25. ©American Audio® - - DCD-PRO600™ Instruction Manual Page 7 GENERAL FUNCTIONS AND CONTROLS - REMOTE UNIT 14 4 16 17 15 13 5 6 12 11 9 7 8 3 2 1 10 Figure 3 26 23 27 20 18 19 30 29 28 24 22 21 25 Figure 4 31 32 33 34 A. REMOTE CONTROL - FACE (FIGURE 3) 1. FILTER/COAST/ADJUST - This button allow you to change the FILTER and Coast values. With the FILTER/COAST/ADJUST button selected (on) the FILTER value is one second and the COAST value is five seconds. With the FILTER/COAST/ ADJUST deselected (off) the FILTER value is a 1/ 2 second and the COAST value is three seconds. A yellow LED will indicated on and off functions. 2. CUE MEMORY - This button allows you to program up to 4 cue points on the CD. For more information on setting a cue point see page 20. 3. FILTER - This button activates the FILTER effect. This effect simulates the sudden platter stop of a turntable. Almost like pressing the stop button on a turntable. When the FILTER effect is selected a number 1 will appear in the LCD (14), this indicates the FILTER effect is active. See "FILTER" effect on page 27. 4. REV/PLAY - This button activates reverse play mode. When this effect is selected the disc will begin to play in reverse mode, and continue to play in reverse until reverse play function is turned off. If reverse play is not turned off the disc will continue to play in reverse until it returns ©American Audio® - - DCD-PRO600™ Instruction Manual Page 8 to the beginning of the disc. When the REV/PLAY effect is selected a number 3 will appear in the LCD (14), indicating REV/PLAY is active. See reverse play on page 24. 5. TIME - The TIME button is used to changed the displayed time values. Time can be displayed as elapsed track time, remaining track time, and total disc remaining time. 6. CUE BUTTONS - These button are used to store four user programmable “Cue Points.” A “Cue Point” is a starting point anywhere on a disc. To program a “Cue Point” see Cue Points on page 18. 7. PITCH BUTTON - This button is used to turn the pitch function on and off. The pitch functions of the PITCH SLIDER (21), PITCH BEND BUTTONS (25) and JOG WHEEL (19) will not function without this function being activated. The pitch percentage value can be changed from (+/- 8%), (+/- 12%) or (+/- 16%). The PITCH BUTTON’s LED will indicate the maximum pitch value by flashing red for 8%, glowing green for 12%, or glowing red for 16%. 8. P. Select (Pitch Select Button) - This button changes the pitch value. The pitch percentage can be changed between 8%, 12%, and 16%. 8% will allow the least amount of pitch manipulation and 16% will allow the most amount of pitch manipulation. To adjust to the different values tap this button. The LED next to the Pitch Button (27) will indicate which pitch percentage mode is activated by, flashing red for 8%, glowing green for 12%, or glowing red for 16%. Note, the Pitch Button (27) must be activated to get a LED reading. The pitch values will immediately reflect the amount of pitch being applied to a music source in the CD drive. The pitch value is adjusted by sliding the PITCH SLIDER (21) up and down. 9. SGL/CTN - This button allows the unit's play mode to change between Single and Continuous. In single mode the unit will play a single track and return to cue mode. In continuous mode the unit continues to play track by track and returns to cue mode after all tracks have played. This function also operates in PROGRAM and FLIP FLOP modes. In program mode the continuous function will play all tracks in a program, than return to cue mode on the first track in the program. When using two units in Flip-Flop mode, each unit may be set up to run in either single or continuous. In single mode a unit will play a single track and jump to the next unit. If the next unit is in continuous mode, that unit will play all tracks and jump back to next unit, and so on. 10. OPEN/CLOSE (Disc Tray Open/Close) - This button is used to open and close the disc transport tray door. NOTE: When a disc is loaded, the tray will not open unless the unit is in pause or cue mode. 11. COAST - This button activates the COAST effect. This effect will simulates turning the power off on a turntable, a turntable platter spinning until it slowly loses momentum and stops. When the C...