The skipped track is cleared from the program. To clear all the reservations Press the FP button repeatedly until “K -“ is displayed, Press it once more to cancel the Karaoke programs. The display returns to that of CD play. m If the reserved track number does not exist on the selected disc, the unit stops playing and the display flashes. In this case, press the a> button to skip the error track. Then press the 4 a button to start play with the next reserved track. When the PRGM button is pressed repeatedly in step 1, PRGM is displayed and the unit enters CD program play mode (page 12). To cancel program play, press the n CLEAR button. ENGLISH SETTING THE TIMER 1 3 2,4 1,2 ‘-M The unit can be turned on at a specified time every day with the built-in timer. Preparation Make sure the clock is set correctly. (See page 6.) Use the remote control. Press the TIMER button on the remote control once to display 0, and press the II SET button within 4 seconds. @k displayed, and the hour flashes. q m If you do not press the 1[ SET button within 4 seconds, another operation may start. Designate the hour of the timer-on time by pressing the 1<< DOWN or a>1 UP button, and the II SET button. Repeat to designate the minute of the timer-on time. After you designate the timer-on time, TIMER and one of the source name flashes alternately on the display for 4 seconds. Within 4 seconds, press one of the function buttons to select a source, “TIMER and the selected source name flash alternately for 4 seconds. At this time, the selected function button does not light up. If this step is not completed within 4 seconds, repeat from step 1. If the TUNER button is pressed, the band cannot be selected in this step. Within 4 seconds, select the duration for the timer-activated period with the l<< DOWN or P>l UP button. The duration for the timer-activated period can beset between 10 and 240 minutes in 10-minute steps. if this step is not completed within 4 seconds, repeat from step 1. 5 Prepare the source. To listen to a CD, load the disc to be played first on tray 1. To listen to a tape, insert the tape into deck 1 or 2. To listen to the radio, tune in to a station. 6 Press the POWER button to turn the unit off after adjusting the volume and tone. @ remains on the display after the power is turned off (timer standby mode). When the timer-on time is reached, the unit turns on and begins play with the selected source. To check the specified time and source Press the TIMER button on the remote control. The timer-on time and the selected source name are displayed for 4 seconds. However, the duration for the timer-activated period will not be displayed. TIMER RECORDING Timer recording is applicable for TUNER and VIDEO/AUX (with an external timer) sources only. Press the TIMER button twice on the remote control so that ~ appears on the display, and press the II SET btiton within 4 seconds. Repeat the steps shown above from step 2 and insert the tape to be recorded into deck 2 after step 5. To cancel timer standby mode temporarily Press the TIMER button on the remote control so that @ or $2 disappears on the display. To restore the timer standby mode, press again to display 0 or Using the unit while the timer is set You can use the unit normally after setting the timer. Before turning off the power, repeat step 5 to prepare the source, and adjust the volume and tone. Timer playback and timer recording will not begin unless the power is turned off. Connected equipment cannot be turned on and off by the built- in timer of this unit. Use an external timer. 21 ENGLISH SETTING THE SLEEP T MER 1 2 The unit can be turned off automatically at a specified time, Use the remote control. 1 Press the SLEEP button. 2 Within 4 seconds, press the +< or >F button to specify the time-until the power is turned off. Each time the button is pressed, the time changes between 10 and 240 minutes in 10-minute steps. Specified time 10 check the time remaining until the power is turned off Press the SLEEP button once. The remaining time is displayed for 4 seconds. 10 cancel the sleep timer Press the SLEEP button twice so that “SLEEP” on the display disappears. CONNECTING OPTIONAL EQUIPMENT Refer to the operating instructions of the connected equipment for details. The connecting cords are not supplied. Obtain the necessary connecting cords. c Consult your local Aiwa dealer for optional equipment, VIDEO/AUX JACKS This unit can input analog sound signals through these jacks, Use a cable with RCA phono plugs to connect audio equipment (turntables, LD players, VCRs, TV, etc.), Connect the red plug to the R jack, and the white plug to the L jack. When connecting a turntable Use an Aiwa turntable equipped with a built-in equalizer amplifier, LINE OUT JACKS This unit can output analog sound signal through these jacks. Use a cable with RCA phono plugs to connect audio equipment with LINE IN (analog input) jacks. CD DIGITAL OUT (OPTICAL) JACK This unit can output CD digital sou...