Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Do NOT attach paper or tape etc. to a disc. . Do NOT expose the discs to direct sunlight or excessive heat. Clean the discs before inserting them into the disc magazine. Always clean a disc from the center outward with a cleaning cloth. There may be burrs left on the inner and outer edges of a brand-new disc. The burr may cause the malfunction of the unit or sound dropout. To prevent these problems, if the burr is left on the disc, be sure to remove them with a ball-point pen, etc. as illustrated. Ball-point pen Burr Burr @ Ball-point pen % NEVER usesolventssuch as benzineoralcohol to clean a disc. . You cannot play an 8-cm (3-inch) CD — even with the specially designed adaptor. . Do NOT use irregular shape CDs (example: heart-shaped, octagonal ones). It may result in malfunction. Notes on the disc magazine . Do NOT leave the disc magazine in a place subject to excessive temperature or humidity. l Do NOT insert more than one disc per slot. Do NOT drop the disc magazine. ENGLISH 2 n UNPACKING Compact disc changer Compact disc magazine Connecting cable Supplied mounting kit for the compact disc changer The letters are keyed to those in the instructions. Use only the supplied mounting hardware for safe and secure installation. @ Brackets (1 pair) @ Washer screws @ Plate brackets @ Nuts (4 ea.) (4 ea.) (2 ea.) @ Adhesive label (1 sheet) 3 ENGLISH lINSTALLATIONS Precautions Select the mounting location very carefully, referring to the following points. . Make sure that there is no fuel tank, wiring or piping on the other side of the mounting surface. Make sure that the installation of the unit will not hinder the movement of the deck lid or interfere with the spare tire, etc. Use only the supplied mounting kit for safe and proper installation. Removing the transpotl screws Find the three transport screws at the bottom of theunit, which lockthe unit’smechanism during transport. Remove these screws before installation. Retain these screws and replace them in the original positions if the unit is transported for service or maintenance. Mounting angle setting levers Be sure to change the position of both mounting angle setting levers according to the angle at which the unit is to be installed. Mounti~g angle setting levers 45’ 45 Q RIZONTAL HORIZONTAL 0 n ‘if “g Insert a ~ointed obiect such as a screw driver or ball-point pen, etc.-into the low spot of the lever and slide the lever to the position from among HORIZONTAL, 45°, and VERTICAL positions. Notes . Be sure to eject the disc magazine when you set the levers. l Be sure to set both levers to the same position. . Be sure to set the levers exactly at the position (notch). If the lever is deviate from the position, the sound may drop out. . Care must be taken when you mount the unit at the angle of lower than level. The disc magazine may drop if you eject the magazine. . Do NOT turn over the unit or slide the lever when the unit is activated. Doing so maydamagethe mechanism or the discs in the unit. . The mounting angle setting levers on each side of the unit are factory-set to the HORIZONTAL position. . When you complete the setilng, attach the supplied adhesive labels @ over the slots. ~ ,,.-,0 ,,, ,,., I ;,” , : ,,/ /@ ., i do ENGLISH 4 ~ INSTALLATIONS Horizontal installation Construction For details on @@@..., see page 3. The effective angle of the unit. The position of the lever. 450 ,n Note HORIZONTAL If the mounting surface needs to be strengthened, r secure the plate brackets @to the bottom surfece of the car trunk, etc. with the tapping screws (not supplied). 2 Deciding the position 4 Making holes in the carpet /’”/ v Removing temporarily ~ Completion 5 ENGLISH Vertical installation Construction For details on @@@..., see page 3. The effective angle of IThe position of the unit, the lever. Notes l If the mounting surface needs to be strengthened, . If installation space is narrow, bend the plate bracket secure the plate brackets @ to the bottom surface ~eb:;:and forth along the perforated line to break off of the car trunk, etc. with the tapping screws (not suppliad). 2 Deciding the position Making holes in the carpet 3 Removing temporarily Completion ENGLISH 6 ~ INSTALLATIONS Suspended installation Caution Before drilling the holes, make sure that there is When installing the unit in the trunk below the nothing on the other side of the mounting surface. package tray, observe the following. Select the mounting location carefully so that the unit does not hinder the movement of the torsion bars of the deck lid. Construction 9 For details on @@@..., see page 3. The effective angle of the unit. 4!3 u HORIZONTAL (f” 2 Making holes 3 Completion Tapping screwe are not supplied. Slanted installation Note on the brackets@ A A Be sure to set the To save installation space, you can place the 15“ mounting angle brackets @ inside out, as illustrated below. 15“ setting levers to the 45° position. 45” “. . . a . 7 ENGLISH lCONNECTIONS This unit is designed only for AIW...