Оценок - 4, средний балл: 4
(
)
)
|
Фото и характеристики Clarion DB315 |
Фрагмент инструкции
. Radio Mode Operations FM Reception ® For enhanced FM performance the tuner includes signal actuated stereo control and Multipath noise reduction circuits. Listening to the Radio 1) Press the FNC button 3 to select the radio mode, then the radio will be on. 2) To select a preset band, press the BND button @, then select one of the preset bands such as FM1, FM2, FM3, or AM. Every time the BND button @ is pressed, the display will change as: FM1 U FM2 U FM3 U AM U FM1 3) Press the SRCH Left/Right button #, then the station at which there is a broadcast will be selected (Seek selection). Mute Use this function to turn off the sound immediately. Press the MUTE button %. The sound turns off and “MUTE ” appears on the display. Press the MUTE button again to cancel the mute mode. Manual Tuning 1) Press the BND button @, then select FM1, FM2, FM3 or AM. 2) Press and hold the BND button @ for 1 second or longer, then the display will show “MANU ”, which means that a manual selection function is on. 3) Press the SRCH Left/Right button # and select the right station. Seek Tuning 1) Press the BND button @, then select FM1, FM2, FM3 or AM. 2) If the “MANU ” on the display is on, press and hold the BND button @ for 1 second or longer. When the “MANU ” display is off, the Seek Selection function is on. 3) Press the SRCH Left/Right button #, then when it selects the station in which there is a broadcast, it automatically stops. DB315 11 E glis English Preset Memory Function Preset Memory Function can store up to 24 stations: six stations for each of FM1, FM2, FM3 and AM. Note: • When the present memory function is used, all the content of the memory will be erased. Manual memory function 1) Press the BND button @, and select the band you want to store in the memory. 2) Press the SRCH Left/Right button # then select the station you want to store in the memory. 3) Press and hold the Preset button 0 for 2 seconds or longer, then the station will be stored in the memory. Auto store function (Automatic Station Store) 1) Press the BND button @, then select the band you want to store in the memory. 2) Press and hold the AS button 9 for 2 seconds or longer, then the station at which the reception is the strongest will be automatically stored in the memory. Note: • When the number of stations stored is less than six, the previous content of the memory for each direct button will be retained. Preset Scanning (Preset Station Scan) When the PS button 9 is pressed, the preset memory numbers flash and the stations are tuned in for 7 seconds each in the order in which they were stored. Press the PS button again to cancel the preset scanning mode. Instant Station Recall (ISR) With this function, a specific radio station can be recalled from any mode. ISR memory 1) Press the FNC button 3, then select the radio mode. 2) Select the radio station which you want to store in the memory. 3) Press and hold the ISR button 5 for 2 seconds or longer. Recalling ISR Press the ISR button 5 then the display will show “ISR”, then the radio station previously memorized will be selected. Press the ISR button 5 again to disengage the unit from the Recalling ISR function. Area Change Use this function when you are using the car stereo anywhere outside the U.S. Switchable frequency spacing This car stereo is initially set to tune in frequency intervals of 10 kHz for AM and 200 kHz for FM, the standard calibrations in the U.S. When using the unit outside the U.S., use the following procedure to switch the frequency range. The table below lists the frequency specifications for the U.S. and other countries. Initial Setting (U.S. standard) New Setting (outside U.S.) AM Frequency spacing 10 kHz 9 kHz Frequency range 530 to 1,710 kHz 531 to 1,629 kHz FM Frequency spacing 200 kHz 50 kHz Frequency range 87.9 to 107.9 MHz 87.5 to 108 MHz Switching the area change Outside U.S. (New Setting) While pressing the BND button @, press the SRCH Left button #, then “outside U.S.” will be selected. Inside U.S. standard (Initial Setting) While pressing the BND button @, press the SRCH Right button #, then the “U.S. standard” will be selected. 12 DB315 CD Mode Operations Loading a Disc Insert the disc into the CD insertion slot with its label side up, then the CD will start playing. For 5-inch (12 cm) CD For 3-inch (8 cm) single CD * When inserting a single CD (3”(8 cm)), insert it from the center of the slot. * When inserting a single CD (3”(8 cm)), do not connect an adapter. * Press the DISP button 6, then the display will show the play time. Notes: • Some CDs recorded in CD-R mode may not be usable. • Even when recorded in CD-R/W mode, some CDs may not be usable. Listening to the Disc already Inserted Press the FNC button 3 to select the CD mode, the CD will start playing. Stopping (pausing) Playback Press the Play/Pause button %. Press the Play/Pause button % again to resume playback. Ejecting the CD Press the Eject button 4, then the CD will be ejected. Note: • If the eject...