Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
You will need to use it again during this setup procedure. 1. Plug the Bose® link cable from the changer into the Bose® link connector on your Wave® music system. 2. Plug the AC power cord from the changer into the AC power input connector on the back of the Wave® music system. 3. Plug the Wave® music system AC power cord into the AC power input connector on the back of the changer. 4. Plug the other end of the power cord into an AC (mains) wall outlet. For best FM reception, straighten the power cord as much as possible. Your Wave® music system uses the power cord as an FM antenna. IMPORTANT 5. Make sure you perform step 5. This enables your Wave® music .. system to operate the disc changer. Turn to “Updating your Wave® music system” on page 7 and follow the instructions for running the Wave® music system update disc. Bose® link connector Wave® music system AC POWER input Wave® music system AC power cord Bose® link cable Wave® music system Multi-CD Changer Changer power cord For best FM reception, straighten the power cord as much as .. possible. 1 2 3 4 4 Setup Setup ® music system To enable your Wave® music system to operate the Multi-CD Changer, run the update disc included with the changer. The display will tell you when the update is finished. 1. Insert the update disc into the Wave® music system CD slot (not into a changer CD slot). 2. Wait approximately 20 seconds while your Wave® music system performs the update. The display will show you a series of messages during this process: LOADING UPDATING FINISHED EJECTING 3. Wait for the system to automatically eject the update disc after updating is finished. DO NOT eject the disc yourself. After updating your system, refer to “Operation” on page 8 for operating information. Wave® music system update disc English 7 Operation English Operation English Remote control guide An additional remote control is included with your Wave® music system Multi-CD Changer. This remote is identical to the one used to control your Wave® music system. So, you can use either remote to control the completed multi-CD system. Just aim the remote at the front panel and press the buttons. The remote normally works within 20 feet of the front panel. The following diagram describes the buttons used for playing CDs using the disc changer. Seek/Track • Press: Skips to next/previous CD track on the current disc. • Press and hold: Rapidly skips to next/ previous CD track on the current disc. Tune/MP3 • Press: Navigates between folders when playing MP3 CDs. • Press and hold: Rapidly scans forward/ backward through a CD track. Play Mode • Selects CD play modes (page 11). CD • Press: Selects the CD source (page 10). • Press again: Moves to the next disc (page 10). AUX • Press to hear audio from an external source connected to either the AUX 1 or AUX 2 input on the changer (page 12). • Press to switch between the AUX 1 and AUX 2 input (page 12). Stop/Eject • Press once: Stops playing the current CD (page 10). • Press again: Ejects the stopped CD. • Press and hold: Ejects a playing CD. Play/Pause • Press: Plays the current CD. • Press again: Pauses a playing CD. Note: Press-and-hold operations require holding the button down for at least one second. Note: Pressing FM/AM, CD, or AUX automatically turns on the Wave® music system to the source selected. Throughout this owner’s guide you will see button icons to the left of the operating instructions. These icons refer to buttons located on the remote control. Turning your multi-CD system on and off Press On/Off once to turn your multi-CD Wave® music system on or off. The system turns on to the last source played. If the last source was CD, the last disc selected starts to play. Press On/Off again to turn the system off. OR Press CD to turn the system on to the CD source. The last disc selected will play. 8 Operation Operation ® music system Insert the disc, label side up, into the CD slot below the display. The disc player will automatically pull the disc in and begin playing. Press CD if the CD source is not selected. Loading CDs into the Multi-CD Changer 1. Insert a disc, label side up, into an empty slot. An empty slot is indicated by an unlit disc slot indicator. 2. With your fingers on the outside edge of the disc, push the disc all the way into the slot . Disc slot indicators Off .......................... Empty disc slot. Pulsating green ...... The disc slot contains a CD which is playing, paused, or in a fast forward/backward scan. Solid green.............The disc slot contains a CD, but it is not currently playing. Solid amber............The CD is being ejected. CAUTION: • DO NOT INSERT mini CDs or non-circular CDs into the disc changer. These discs may not play properly and could interfere with the system’s ability to eject them. • DO NOT INSERT more than one disc at a time into any disc changer slot. Doing so can cause damage to the disc and/or the disc changer. English 9 Operation English Operation English Playing CDs With the Mult...