Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Make sure the legs are pushed up all the way. If you decide to wall mount your MS3105 audio system please read and carefully follow these instructions: NOTE: Wall mounting hardware is not included. You should purchase the appropriate type of anchors for the wall where the unit will be mounted. (Solid-wall, Hollow-wall, etc.) Wall anchors are available at hardware stores and home improvement centers. Tools required: Electric drill, Hammer, Screwdriver. General Precautions and Recommendations • When choosing a location for wall mounting remember that the main unit must be connected to an AC outlet. The AC power cord of the main unit should be able to hang straight down from the main unit to the AC outlet. See Figure 1. Connect the main unit to the AC outlet and position it against the wall in your desired location. Make sure that the plug remains firmly and full inserted into the outlet. There should be just enough slack in the power cord so that the plug can be easily removed from, and reconnected to the AC outlet. WALL MOUNTING INSTRUCTIONS Correct Incorrect Figure 1 MS3105_120503.p65 31 5/12/2003, 12:03 32 • Have someone hold the main unit against the wall in the desired location and make a pencil mark on the wall to indicate center point of the top edge of the cabinet. • If there is no AC outlet directly below the desired mounting location you may use a UL approved extension cord. In this case you should allow the AC plug of the main unit to reach all the way to the floor and connect the extension cord on the floor, not above the floor. See Figure 2. • Although all major functions of this system, including opening/closing the front cover, can be operated by the remote control, you must still load and unload your CD's manually. Therefore the main unit should be mounted at a height that is convenient and comfortable for changing discs. IMPORTANT: The front cover requires 3" clearance to open fully. If you plan to mount the unit under a shelf, in a cabinet. etc, you must allow at least 3" clearance above the unit so that the door can open completely without obstruction. If the front cover encounters some obstruction as it is opening, the motor will reverse automatically and the door will close immediately. PENCIL MARK AT CENTER Correct Incorrect Figure 2 MS3105_120503.p65 32 5/12/2003, 12:03 TEMPLATE INSTRUCTIONS 1.) Select the desired location for wall mounting after carefully reviewing the "General Precautions and Recommendations" of the wall mounting instructions. 2.) Tape the template to the wall, or other surface, in the desired location. Align the top edge of the template with the pencil mark you made on the wall. Be sure to allow at least 3" clearance above the main unit, for the CD door to open fully. 3.) Make sure that the template is level. 4.) Use an awl, ice pick, a nail or similar pointed tool, and push through the template to make a small starter hole in the wall surface as indicated by the "Drill Hole Here" marks. Then remove the template from the wall. 5.) Before You Drill: Make sure that there are no water plpes, gas pipes, electrical wires on other obstructions or hazards behind the wall in your chosen mounting location. If you are not sure about this. and don't know how to check, perhaps you should consider having the system mounted by someone with the necessary experience. 6.) Make sure that you are using the correct type of anchors for your wall. If the wall material is Sheetrock® (sometimes called wall-board, gypsum-board, or plaster-board) you can use plastic ‘hollow-wall anchors’. If your wall is solid plaster, concrete, brick, or similar solid material, use the appropriate type of ‘solid-wall anchors’. If your wall is solid wood, you may be able to use round- head wood screws without anchors. IMPORTANT: If you have no experience installing wall anchors you should have this system mounted by someone who does have the proper experience. Whichever type anchors you use, make sure that the diameter of the screw heads is at least 1/4”. Follow the instructions supplied with the wall anchors to determine the proper size drill bit to use in your electric drill. After installing the proper size bit, drill holes in the wall surface at the 4 locations where you made the starter holes in Step 4. 33 MS3105_120503.p65 33 5/12/2003, 12:03 7.) Insert the tip of the anchor into each hole and use a hammer to tap the anchors all the way in until they are flush with the wall surface. 8.) Insert the screw into the anchor and tighten the screw until it touches the collar on the anchor. This causes the anchor to spread inside the wall and locks the anchor in place. 9.) Loosen the screw until there is a gap about 1/8" between the screw head and the wall. 34 MS3105_120503.p65 34 5/12/2003, 12:03 10.) Position the main unit over the two screw heads so that the heads of the screws fit into bottom of each "Keyhole" on the back cabinet. When the two screw heads are inside the keyholes, slide the main unit slightl...