Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
7 NR52_010704.p65 7 7/1/2004, 11:53 OPERATING INSTRUCTIONS LISTENING TO THE RADIO 1.) To turn the system ‘on’, rotate the ON/OFF-VOLUME control clockwise until a ‘click’ is heard, and set the Volume to a low level. The Tuning Dial light comes ‘on’. 2.) Set the Function selector (AM/FM/CD) to the desired band. 3.) Rotate the TUNING control to tune to the desired radio station. 4.) Adjust the ON/OFF-VOLUME and TONE control to the desired level. 5.) When you are finished listening turn the ON/OFF-VOLUME control counter clockwise until a ‘click’ is heard. Antenna Information The AM antenna is inside the cabinet. If AM reception is unsatisfactory try repositioning the cabinet slightly until the internal antenna is picking up the strongest signal. The FM wire antenna is located on the back cabinet. If necessary adjust the position and direction of this antenna until you find the position that provides the best reception. 8 NR52_010704.p65 8 7/1/2004, 11:53 PLAYING COMPACT DISCS 1.) Turn the ON/OFF-VOLUME control clockwise until a ‘click’ is heard, and set the volume to a low level. 2.) Set the Function selector (AM/FM/CD) to the CD position. The CD track number display comes ‘on’. 3.) Press the CD DOOR OPEN/CLOSE button to open the CD door. Lift the CD clamper arm, remove the transit card which was used to secure the laser during shipment and dispose of this card 4.) Place your disc on the CD spindle with the printed label side facing up and lower the CD clamper arm. The disc will spin for a few seconds while the player reads the disc, then the disc stops and the display shows the total number of tracks on the disc. 5.) Press the CD PLAY/PAUSE button to begin playback on track number one. The Play indicator comes “on” PLAY/PAUSE Note: You may leave the CD door open during playback if you wish, but we recommend closing the door again for better sound and also to prevent excess dust from accumulating on the CD spindle. 6.) Adjust the ON/OFF-VOLUME and TONE controls to the desired level. 7.) Playback will continue until the end of the disc. When the disc ends the display again shows the total number of tracks on the disc. You may also stop playback at any time by pressing the CD STOP button. Pause Control To pause momentarily during playback press the CD PLAY/PAUSE button again. Playback stops but the disc continues to spin and the Play indicator flashes. Press the CD PLAY/PAUSE button PLAY/PAUSE once more to cancel Pause and resume playback. The Track Number display stops flashing. 9 NR52_010704.p65 9 7/1/2004, 11:53 Skipping Tracks and High Speed Music Search During CD Playback, repeatedly press the F. SKIP (Forward Skip) or B. SKIP (Back Skip) buttons to skip to higher or lower number tracks. When the desired track number appears on the display release the buttons and playback will begin on the desired track. To rapidly search forward or back within a track to locate a specific musical passage, depress and hold either the F. SKIP (Forward Skip) or B. SKIP (Back Skip) buttons. The player will move forward or backward at high speed as long as the buttons are depressed. When you hear the desired passage release the buttons. Normal playback will resume at that point. Repeat Playback This feature allows you to continuously repeat a single track or the entire disc. To Repeat A Single Track Press the REPEAT button once. The Repeat indicator flashes. REPEAT Press the or buttons to select the desired track, then press the CD PLAY/PAUSE button to begin Repeat Playback of the selected track. To Repeat The Entire Disc Press the REPEAT button twice. The Repeat indicator REPEAT remains ‘on’. Press the CD PLAY/PAUSE button to begin Repeat Playback of the entire disc. To cancel Repeat Playback press the REPEAT button until the Repeat Indicator goes ‘off’. Repeat Playback is also canceled by pressing the STOP button, or setting the Function selector to the AM or FM position. 10 NR52_010704.p65 10 7/1/2004, 11:53 PROGRAMMED PLAYBACK This feature allows you to program up to 20 tracks on a disc for playback in any desired order. Note: You cannot program tracks while a disc is playing. If the disc is playing press the STOP button first before beginning the programming steps below: PRG. 1.) Press the PRG. button to enter the Program Mode. The Program indicator and Program number ‘01’ flash. PRG. 2.) Press the F. SKIP or B. SKIP buttons to select the first track number you wish to enter in the program memory. Example: Track Number 8. PRG. 3.) When the desired track number appears on the display, press the PRG. button again to enter that track in memory. The program number display advances to “02”. 4.) Repeat Steps 2-3, selecting a different track number each time until you have entered up to 20 tracks in the program memory. Note: You may program the same track number to play multiple times in the program sequence if desired. 5.) Press the PLAY/PAUSE button to begin PRG. Programmed Playback. The Program indicator stops flashing and rema...