Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
(refer to the sound card documentation for further details) 3. Master/slave select terminal. 4. 40pin host IDE interface connector. 5. 4pin power terminal. (A : +5V DC) (B : +12V DC) SAMSUNG I everyone’s invited-п ¡ DIGrTí///) Setup 1, Make sure that the PC is powered off and disconnected from any power source. 2, If necessary, attach a horizontal bracket to both sides of the drive. ij Remove the cover from a free expansion slot and install the DVD-ROM drive, as shown in the ' illustration. SAMSUNG DIGI Tau) everyone’s invite<1тм Setup Connecting the power cable * The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal on the rear of the Optical drive drive. 1 +5V DC 2 Ground 3 Ground 4 +12V DC Note: An improperly connected power cable may cause trouble. Check the direction of the power connector and the incline S-IDE of the Optical drive before connecting. Connecting the E-IDE cable Insert the E-IDE cable (40-pin), which is connected to the hard disk to the interface terminal. (Place the red line of the cable close to the Pin 1.) ^ When using one E-IDE cable Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear of the Optical drive. a : Slave Drive (Choose the SL Jumper) b : Hard Drive c : MainBoard ^ When using two E-IDE cable * If there is only one Optical drive, select MA (Master). SAMSUNG DIG i) everyone’s in Setup a : Master Drive (Choose the MA Jumper) b : Hard Drive c : MainBoard d : Primary 1 e : Secondly 1 * If there is two Optical drive, select MA (Master) / SL (Slave). -Jr a : Master Drive (Choose the MA Jumper) b : Slave Drive (Choose the SL Jumper) c : Hard Drive d : MainBoard e : Primary 1 f : Secondly 1 .j*' Installing a jumper on the master/slave select terminal SAMSUNG DIG everyone’s in Setup Connect a jumper to the rear S-IDE of the Optical drive. If the jumper is connected to MA (Master), it will work in the Master mode. If the jumper is connected to SL (Slave), it will work in the Slave mode. If the jumper is connected to CS (CSEL), you can control the device by using the host interface signal CSEL. (In general, connection to MA is recommended.) •r Connecting the audio cable from a sound card * Connect the 4-pin audio cable between the sound output terminal on the Optical drive and the audio input terminal on the sound card. * For clearer sound, use a digital output terminal.(Available only for the CARD that supports digital output) This may not be available for general sound cards. SAMSUNG DIG everyone’s in Setup * Installing the Device Driver This Device Driver is an installation driver that can detect ODD (Optical Disc Drive) products in DOS mode. It provides only the reading function in Dos mode. (For recording, it is recommend not to install the Device Driver designed for DOS mode) The Device Driver for DOS mode is included in the Ddriver or DOS Driver folder of the disc enclosed with the product that you purchased. I For Windows98/2000/ME/XP or higher version that uses a device driver provided by Windows, l£'-‘ there is no need to set up an extra device driver. Refer to the steps below to see if Windows detects the drive. f a Double-click on the My Computer icon on your desktop. 2, Double-click on the Control Panel folder. is Double-click on the System icon. >i Click on the Device Manager tab. f- Expand the CD-ROM branch. "■ The Installing the Device Driver device name is displayed. SAMSUNG DIG everyone’s in Setup ' Setting Up the Device Driver The device driver is located in the Ddriver folder of the User's Guide disc with is provided in the package. This device driver is to recognize a DVD-ROM drive on Dos mode. This driver should be applied for DOS mode user to install on Windows 98 or Windows ME only. > Automatic Setup f, Insert the User's Guide disc into the CD-ROM drive and open the Ddriver folder. .2, Run the CDSETUP.EXE file in the Ddriver folder. 3,, When Setup is successfully completed, click OK button or press the Enter key. ■ p Reboot the computer. Manual Setup T. 2. S. Make the C:\SAMSUNG directory. Copy the files from the User's Guide disc to the C:\SAMSUNG directory. To do so, type COPY D:\Ddriver * . * C:\SAMSUNG after the C:\prompt and press [Enter]. Edit the CONFIG.SYS file. Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000/V entry. î 18.W ¥ i4 Ц-: ",V IBDV Edit the AUTOEXEC.BAT file. Add the C:\SAMSUNG\MSCDEX/D:SSCD000 entry. I -.UTJ Mi41m II 'ïvi 1ВЫ Reboot the computer. SAMSUNG DIGIТай) everyone’s invite
CD/DVD приводы - SH-D162D (386.75 kb)
CD/DVD приводы - TS-H352C (386.75 kb)