Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
Make sure to close all working programs before attempting to open the tray and always use the open/close button. о Do not insert a pin into the emergency opening while in operation. Do not disassemble, attempt to repair or modify the device without express approval as directed in the manual. • To reduce the risk of damage, electric shock, and fire. Do not use cracked, distorted or damaged discs. •A о о In particular, a disc with a crack on the inner tracks may break while in use. 'A Important to read and understand at all times Do not disassemble 1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended that you make a copy immediately and use the copy instead. When a cracked disc is used continuously, the size of the crack is likely to grow and it will eventually result in inseparable damage to the disc. 2. Do not use low quality discs (i.e., illegal products, scratched or damaged discs). Introduction °y Design and specifications are subject to change without prior notice. Eject Button If the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfolded paper clip in the hole and push firmlhy) Sound output terminal Interface terminal Rear Digital output Master/slave select terminal Power terminal terminal Accessories- EIDE cable, 4 screws. J Design and specifications are subject to change without prior notice. Connecting the Cables to the CD-Rom Connecting the Cables Power cable EIDE cable Master/slave select terminal Audio cable 2 3 Connecting the power cable • The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal the rear of the CD-ROM drive. Connecting the EIDE cable • Insert the EIDE cable (40-pin), which is connected to the hard disk to the interface terminal. (Place the red line of the cable close to the Pin 1.) Installing a jumper on the master/slave select terminal • Connect a jumper to the rear side of the CD-ROM. If the jumper is connected to MA (Master), it will work in the Master mode. If the jumper is connected to SL (Slave), it will work in the Slave mode. If the jumper is connected to CS (CSEL), you can control the device by using the host interface signal CSEL. (In general, connection to MA is recommended.) CS : Cable Select(CSEL) SL : Slave MA: Master 4 Connecting the audio cable from a sound card • Connect the 4-pin audio cable between the sound output terminal on the CD-ROM drive and the audio input terminal on the sound card. 2 3 4 When using one EIDE cable Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear of the CD-ROM drive. When using two EIDE cable • Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear of the CD-ROM drive. - If there is only one Optical drive: select MA (Master). -If there is two Optical drive, select MA (Master) / SL (Slave). Master Drive (Choose the MA Jumper) Slave Drive (Choose the SL Jumper) SEC 1 PRI 1 Hard Drive (Choose the MA Jumper) (Choose the SL Jumper) MainBoard Installing the Drive System Requirements Intel Pentium 166MHz(or higher), 16 MB of RAM (or higher) with an EIDE interface, Windows 98 / 2000 / ME / XP Windows NT 4.0 (or higher) Installing the CD-Rom Drive How to install the CD-ROM drive on your PC. First, remove the cover; connect the cable to the CD-ROM drive and then to the PC. 1 If necessary, attach a horizontal bracket to both sides of the drive. • You can purchase these accessories separately from your computer dealer. (Screws for use: M3 X 6 X 4) 2 Remove the plate from a free expansion slot and install the CD-ROM drive, as shown in the illustration. • If you have no free expansion slot, install the drive in place of the diskette drive. • Make sure to use the standardized screws supplied (M3X6). - To use screws other than M3X6 may result in malfunction. Using the Drive/Storing and Cleaning Your Discs Using the CD-ROM Drive 1 2 3 4 Push the power button and boot the computer. After booting the computer, open the disc compartment by pressing the Eject button. Insert the disc (CD) with the label on the disc facing upwards and close the disc compartment by pressing the Eject button. The indicator light comes on. Play the disc (CD). Playing CD-DA/Audio CDs • Run the CD player program supplied with the sound card or play the Windows Media Player. Playing Video CDs • Follow the instructions provided with the disc. • A video card or MPEG software and a sound card need to be installed to view video CDs. • If the drive is vertically installed, you cannot use an 8 cm MiniDisc because the disc is movable. Storing Your Discs Do not place a disc in direct sunlight. Store a disc vertically in a well-ventilated and stable location. Do not write or attach a label on a disc. Do not drop a disc or place heavy objects...
Эта инструкция также подходит к моделям:CD/DVD приводы - TS-H192C (782.36 kb)