Оценок - 4, средний балл: 4
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Auto Normally select this. Off Select this when the picture is unstable or colours appear unnatural. Pause Mode Sets the picture mode for DVD playback pause status. For BD-ROMs or discs containing AVCHD files, “Pause Mode” automatically switches to “Auto.” Audio Settings The default settings are underlined. Audio Output Priority Selects the jack type to output audio signals. 2-channel Linear PCM signals are output at 48 kHz maximum from output jacks other than the priority jacks. HDMI Outputs audio signals from the HDMI OUT jack. Coaxial/ Optical Outputs audio signals from the DIGITAL OUT (OPTICAL/COAXIAL) jack. Stereo Analogue Outputs audio signals from the LINE OUT (R-AUDIOL) jacks. Audio (HDMI) Selects the signal type for the HDMI OUT jack. Auto Normally select this. Outputs audio signals according to the status of the connected HDMI device. 2ch PCM Downmixes to 2-channel Linear PCM signals before outputting from the HDMI OUT jack. b Select “2ch PCM” when connecting a TV or an AV amplifier (receiver) that does not support Dolby Digital or DTS, otherwise noise or no sound may result. Auto Normally select this. Dynamic moving pictures appear without blurring. Frame Displays static pictures at high resolution. BD Audio Setting BD Audio Setting Mix Outputs the audio obtained by mixing the interactive audio and secondary audio to the primary audio. Direct Outputs the primary audio only. b PCM 96 kHz and PCM 192 kHz audio signals are output as PCM 48 kHz audio signals when “BD Audio Setting” is set to “Mix.” Audio ATT Lowers the audio output level to prevent sound distortion. On Enables Audio Attenuation. Off Disables Audio Attenuation. b “Audio ATT” does not affect the output from the HDMI OUT jack and the DIGITAL OUT (OPTICAL/COAXIAL) jack. Dolby Digital Selects the audio signals output when playing Dolby Digital discs. This setting affects the output from the DIGITAL OUT (COAXIAL/OPTICAL) jack. DTS Selects the audio signals output when playing DTS discs. This setting affects the output from the DIGITAL OUT (COAXIAL/ OPTICAL) jack. Downmix PCM Converts to output Linear PCM signals. Select this when connecting to an audio device without a built-in DTS decoder. DTS Select this when connecting to an audio device with a built-in DTS decoder. 48kHz/96kHz PCM Selects the maximum sampling frequency for the PCM signals output from the DIGITAL OUT (OPTICAL/COAXIAL) jack. 48kHz/16bit Outputs audio signals of 96 kHz sampling as 48 kHz/ 16 bit. 96kHz/24bit Outputs audio signals of 96 kHz sampling as 96 kHz/ 24 bit. However, the signals will be output as 48 kHz/ 16 bit if the source is copy- protected. b • If you select “96kHz/24bit” when an AV amplifier (receiver) that does not support 96 kHz is connected, no sound or a loud sound may result. • “48kHz/96kHz PCM” is not effective when “Audio Output Priority” is set to “HDMI” or “Stereo Analogue.” Settings and Adjustments Downmix PCM Converts to output Linear PCM signals. Select this when connecting an audio device without a built-in Dolby Digital decoder. Dolby Digital Select this when connecting an audio device with a built- in Dolby Digital decoder. ,continued Audio DRC Audio DRC Auto Performs playback at the dynamic range specified by the disc (BD-ROM only). Other discs are played back at the “Standard” level. Standard Performs playback at a compression level between “TV Mode” and “Wide Range.” TV Mode Sounds are compressed heavily. Low sounds are easier to hear. Wide Range No compression works. A more dynamic sound is produced. b • “Audio DRC” is effective only when playing Dolby Digital, Dolby Digital Plus, and Dolby TrueHD audio signals. • When “Dolby Digital” is set to “Dolby Digital” in the “Audio Settings” setup (page 45), “Audio DRC” has no effect on the audio output from the DIGITAL OUT (OPTICAL/COAXIAL) jack. However, this excludes the following cases. – when “BD Audio Setting” is set to “Mix” when playing a BD. – when “Audio Output Priority” is set to “HDMI” or “Stereo Analogue.” Downmix Sets the downmix method of multi-channel to two-channel sound. Dolby Outputs the Dolby Surround Surround (Pro Logic) signals in 2 channels. Select this when connecting an audio device that supports Dolby Surround (Pro Logic). Normal Outputs audio signals without Dolby Surround (Pro Logic) effect. Select this when connecting an audio device that does not support Dolby Surround (Pro Logic). b “Downmix” has no effect on the bitstream audio output from the DIGITAL OUT (OPTICAL/ COAXIAL)/HDMI OUT jack. Viewing Settings The default settings are underlined. BD/DVD Menu Selects the default menu language for BD- ROMs or DVD VIDEOs. When you select “Select Language Code,” the display for entering the language code appears. Enter the code for your language by referring to “Language Code List” (page 65). Audio Selects the default track language for BD- ROMs or DVD VIDEOs. When you select “Original,” the language given priority in the disc is selected. When you select “Select Language Co...
Эта инструкция также подходит к моделям:Blu-Ray проигрыватели - BDP-S363 (3.22 mb)