Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Battery life will depend on actual usage and amplification levels. Pairing your CLA7BT to your Cellular Phone. “Pairing” Creates a link between devices equipped with Bluetooth wireless technology and the CLA7BT, and allows the phone to remember the Neckloop’s unique ID; you can add it to a list of paired devices in the phone. The CLA7BT should be paired once with the phone before use. If the pairing information or log is deleted from your phone, the unit must be paired again with the phone prior to use. Once your CLA7BT and phone are paired, your CLA7BT automatically connects to your phone if the phone supports that protocol. Some phones may ask if you want to connect to a Bluetooth device. You need to check with your phone’s manual on how Bluetooth works with the phone. With the CLA7BT and phone in close proximity 1 With your CLA7BT off, press and hold the Multi Function Button on the left side of your neckloop for more than 3 seconds. After the LED indicator lights up steadily, the neckloop is in pairing mode. 2 Perform a device discovery from your phone (for the detail on device discovery for your phone, refer to your owner’s manual). When the scan is complete, the phone displays the devices found 3 Select BT 107 from the list of devices discovered and confirm per the requirements of your phone. 4 When prompted by the phone, enter the passkey 0000. Your phone will confirm that bonding occurred and the CLA7BT will confirm it paired successfully with 10 rapid flashes. 5 The phone information is now stored in the CLA7BT memory. NOTE: Make sure the neckloop and phone you are using are no more than 10m/33 feet apart, so they are within operable range. If the neckloop is not successfully paired within 2 minutes, it will automatically leave pairing mode. If you still want pairing, you will need to repeat the steps listed above. Pairing your CLA7BT to Additional Devices. Your CLA7BT can store pairing information for up to eight (8) different devices with Bluetooth wireless capability. Devices are stored in a “Paired Device List” in the memory in a time sequence. When an attempt to pair more than eight devices is made, the oldest paired device is removed from the memory list. Any of the eight paired devices can initiate a connection to the CLA7BT. The neckloop will automatically initiate a connection (once turned on) with the last device to which it was connected. If you want to connect the CLA7BT to another device in the paired device list, you must initiate the connection from that device. When any of the eight devices initiates a connection to your neckloop, that device then becomes the “last connected” device. Wearing the Unit 1. Place the wire around your neck and insert the round connector plug into the Neckloop Quick Disconnect plug, forming a loop. IMPORTANT: To have the Neckloop operate properly, you will need to be sure the Quick Disconnect connection jack has been securely clicked in place. There will be two distinct clicks. 2. Make sure your CLA7BT is paired to the device you wish to use 3. Switch your hearing aid to “T” or “MT” mode when ready to make or receive a call. Turning your CLA7BT On and Off To turn the CLA7BT ON Press the Multi-Function button on the side of the CLA7BT. A series of 4 tones (low to high) can be heard from your hearing aid when it is in t-coil mode and the LED flashes 2 times (0.1 seconds) To turn the CLA7BT OFF Press the Multi-Function button on the side of the CLA7BT. A series of 4 tones (high to low) can be heard from your hearing aid when it is in t-coil mode and the LED flashes 2 times (0.5 seconds) and the LED is off. Receiving Volume Adjustment The receiving volume can be adjusted during a call. Use the volume control knob located on the right side of the unit when it is being worn. The volume setting on the cell phone or other device will add or remove amplification from the overall system. If amplification is low, check the volume level on both units. If there is distortion or other interference, lower the volume on one or both of the units. Too much amplification can cause distortion. Making and Receiving Calls Using Bluetooth The CLA7BT supports both Hands-Free and Headset Profiles. Accessing call functions depends on which profile your phone supports. You can activate all functions for Hands Free Profile using the following table. NOTE: Some phones do not support all features listed. Please consult your phone user’s guide. When pressing the Multi-Function button, you can: Press and Release– refers to duration of less than 0.8 seconds. You should hear 1 beep to confirm the requested action. Press and Hold – refers to a duration of more than 0.8 but less than 1.6 seconds. While holding the multi-function button you will hear one beep, release the Multi-Function button to confirm the requested action. Press and Extend Hold – refers to a duration of more than 3 seconds. While holding the multi-function button you will hear one beep, release the Multi-Function button t...