Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. Federal Communication Commission Interference Statement 5 4 c. While listening to music (for example, song 2), press the Speaker's FORWARD >> button (Fig.2) will skip to next song (for example, song 3); press the BACKWARD << button (Fig.2) will replay the current song (for example, song 2). The fast forward & backward are also supported by holding the FORWARD >> or BACKWARD << function keys. This remote control function is supported only by the AVRCP profile in your enabled devices. d. Turn the Speaker off after use. Remark: Details operation of music playing through A2DP profile varies from different Mobile Phones / PDAs. Bluetooth Bluetooth II. Traveller Speaker paired with Stereo Audio Adaptor BT 65N Guide When you purchase a Combo pack with BT90S Traveller Speaker and BT 65N Stereo Audio Adaptor, please follow this Guide. Bluetooth Audio Adaptor Bluetooth Traveller Speaker 1. Pairing a. While the Speaker is powered off switch the power ON/OFF switch (Key 2) to the “I” position to turn it on (Fig.1). The Power LED (Fig.3) will become blue. Press and hold ON/OFF/Pairing/Pause switch (Fig.2) for 4 seconds, the LED will flash red and green alternatively, which indicates the Speaker in Pairing Mode. The Pairing Mode will last for one minute. b. While the BT 65N Stereo Audio Adaptor is powered off, press and hold PLAY and STOP buttons simultaneously. The LED will flash red and green alternatively, which indicates the Audio Adaptor is in Pairing Mode. The Paring Mode will last for one minute. c. Put the Speaker and the Audio Adaptor close to each other, 0.5 to 3 meters. After a few seconds, their LED's on two devices will turn into flashing green, which indicates successful pairing. Both units are in Standby Mode and ready to transmit audio signal, or music from the audio source (Fig.5). , Bluetooth Bluetooth 2. Listening to music a. After successful pairing, plug the jack of the Audio Adaptor to the 3.5 mm socket of any audio source such as iPod, MP3, CD player, Notebook PC, or other audio devices with audio jack. b. Play the music on the audio source as normal; you will listen to the stereo music from the speaker. c. The Music volume can only be adjusted by pressing and releasing the VOL+ / VOL - buttons of audio source. d. Turn the Speaker off after use and the Audio Adaptor will be turned off automatically. Next time, you don't need to pair them again. Turn them on, and then they will be paired automatically and ready to transmit music from the audio source. III. Traveller Speaker connected directly with Audio Device Guide 1. Listening to music a. While the Speaker is powered off, switch the power ON/OFF switch (Key 2) to the “I” position to turn it on (Fig.1). The Power LED (Fig.3) will become blue. b. Plug one end of the audio cable to the “Audio input socket” (socket 4, Fig.1) of the Traveller Speaker and the other end to the 3.5 mm socket of any audio source such as iPod, MP3, CD player, Notebook PC or other audio devices. c. Play the music on the audio source as normal; you will listen to the stereo music from the speaker. d. The Music volume can only be adjusted by pressing and releasing the VOL + / VOL- buttons of audio source. e. Turn the Speaker off after use. Accessories Table Standalone pack (BT90S) Combo pack (BT90S+BT65N) Included Audio cable Included Incl...
Эта инструкция также подходит к моделям:Беспроводные гарнитуры и прочие аксессуары - BT90S (1.08 mb)