Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
To obtain a replacement, visit our website at or call 1 (888) 915-2007. In Canada, dial 1 (866) 288-4268. Figure 1: Repeater About the repeater You can use a repeater to extend the operating range for the AT&T SB67118 DECT 6.0 4-line corded/cordless telephone system to cover areas where the signal is very weak or not available. The repeater extends the range in all directions, even going around certain barriers. The telephone base, cordless handsets and repeaters are linked through wireless connections. When configured properly, you should not notice any reception problems as you move around within the covered area. Up to six repeaters can be registered to the telephone base. There can be two repeaters in series going between the base and handsets. The first repeater can be up to 950 feet away from the base. The second repeater can be up to 950 feet away from the first repeater. Handsets work up to 950 feet from the base or any repeater, so with two repeaters in series, handsets work up to 2,850 feet away from the base. The figure below shows an example of how you might choose to setup your system. 950 feet 950 feet 950 feet 950 feet 950 feet 950 feet 950 feet 950 feet 950 feet 950 feet 950 feet Figure 2: Planning repeater placement Registration You should register your repeaters to the telephone base before choosing locations for them in the building. NOTE: You can register a repeater to an SB67118 telephone base without deregistering it from a previous telephone base. New registrations overwrite any previous repeater registrations. Repeater registration 1. Plug in the repeater to AC power. The STATUS indicator light on the repeater flashes slowly. 2. Press and hold the SETUP button at the bottom of the repeater for two seconds. The STATUS indicator light on the repeater flashes quickly. 3. On the telephone base, press MENU/ENTER. 4. Scroll down to Registration and press MENU/ENTER. 5. Press MENU/ENTER again to select Register HS. The telephone base screen shows Handset registering during registration. 6. The STATUS indicator light becomes solidly lit when registration is successful. The telephone base screen shows Repeater registered. It takes about 60 seconds to complete the registration. NOTES: If the registration is not successful (the STATUS indicator light is not solidly lit after 60 seconds), the telephone base screen shows Error. Try the Repeater registration process again. A registered repeater does not count as an extension and does not have an assigned extension number within the telephone system. For complete registration instructions of SB67118 telephone base, please refer to the manual provided with your AT&T SB67118 product, or visit to download the manual. STATUS indicator light SETUP button Registration STATUS indicator light Slow flash The repeater is powered on and in idle mode waiting to be re- registered. -OR- The registered repeater is not connected to the telephone base. -OR- Your telephone base has no power. Quick flash The repeater is registering to the telephone base. On The repeater is successfully registered and in a normal operation mode. Off The repeater has no power. Installation After you have plugged in your repeaters in the locations you think are best, place a call from a cordless handset (AT&T SB67108) and while talking, move around the building to test the reception. You may want to adjust the position of repeaters to receive the best reception. Plug the small end of the power adapter into the power jack on the front of the repeater and route the cord through the slot on the bottom of the repeater. Route the power adapter cord through the slot on the bottom of the repeater. Plug the small end of the power adapter into the power jack on the bottom of the repeater. Plug the large end of the power adapter into a standard electrical outlet not controlled by a wall switch. Raise the antennas. Figure 3: Connect the power adapter to the repeater Installation You can place the repeater on a tabletop. You can install your repeater on a wall or other object with the provided screws. Please use the recommended placement and installation tips as follows: The antennas needs to be in a high location (not on the floor or under a desk) for reception. Maintain a minimum of 30 feet distance between each repeater. See page 2 for additional placement information. If you place the repeater on a tabletop, plug the large end of the power adapter into a nearby electrical wall outlet and raise the antennas. Figure 4: Tabletop installation Installation If you want to install your repeater on a wall or other object, use the provided screws. Professional assistance may be required to install screws on the wall. Then plug the large end of the power adapter into a nearby electrical wall outlet and raise the antennas. ^ ^ Screw holes Screw spacing=2.5 inches Figure 5: Wall installation NOTE: ...................................................................