Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
PKG-M30141ES IOGEAR, the IOGEAR logo, are trademarks or registered trademarks of IOGEAR, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. IBM is a registered trademark of International Business Machines, Inc. Macintosh, G3/G4 and iMac are registered trademarks of Apple Computer, Inc. All other brand and product names are trademarks or registered trademarks of their respective holders. IOGEAR makes no warranty of any kind with regards to the information presented in this document. All information furnished here is for informational purposes only and is subject to change without notice. IOGEAR, Inc. assumes no responsibility for any inaccuracies or errors that may appear in this document. Table of Contents Introduction 06 Pairing with a Bluetooth Phone 12 How to use the headset 14 · Making a call 14 · Ending a call 15 · Answering a call 16 Connecting the Headset to PC/laptop 18 Technical Support 27 Limited Warranty 28 Introduction Please refer to the picture on the next page 1. Multi-function button – used to turn headset ON/OFF, activate in discovery mode for pairing, and answer/terminate calls 2. Speaker – this is the speaker for incoming voice calls 3. Power jack – insert power cable to charge internal battery 4. Microphone – this is the microphone for outgoing voice calls 5. LED window – displays red and blue LEDs 6. Volume up – increase the volume on the headset 7. Volume down – decrease the volume on the headset 8. Ear hook - reversible 6 Intr IntrIntrIntroduction oductionoduction 12345678 7 Introduction LED Indicator lights Blue LED: • Flashes approximately every four (4) seconds when the headset is ON (standby mode) • Double flashes every 4 seconds when the headset is connected. Red LED: • Remains ON while headset is charging and also when in discovery mode • Flashes when the headset battery is low. Discovery Mode: • Blue and red light flashes very rapidly when in discovery mode to pair with your Bluetooth phone Turn ON the headset 1. Press and hold the multi-function button for about seven (7) seconds; the blue LED will flash quickly four (4) times. Thereafter, it will flash once every seven (7) seconds. Turn OFF the headset 1. Press and hold the multi-function button for about seven (7) seconds; the red LED will flash four (4) times and then turn off. 8 Introduction Charging the Battery You must charge the internal battery of the Bluetooth headset before your first use. Thereafter, the glimmering red LED will flash when the battery is low and emit a warning sound. To charge the battery, follow the procedure below: 1. Turn OFF the headset 2. Connect AC adapter into the power jack of the Bluetooth headset 3. The Red LED will remain ON while the headset is charging. Once the headset is fully charged, the red LED will turn OFF. It takesabout 2 hours to fully charge the headset. A fully-charged battery will give you approximately 7 hours of talk time, or 170 hours stand-by time. 9 Intr IntrIntrIntroduction oductionoduction Attaching ear hook 1. Position the headset with the speaker pointing inward 2. Position the ear hook with the clip-on facing down 3. Snap the ear hook onto the neck of the speaker TIP: To use the headset on the other ear, insert the ear hook from the ooposite side. (for left ear) . (for right ear) . 10 Intr IntrIntrIntroduction oductionoduction Placing headset on your ear 1. Wrap the ear hook around your ear 2. Insert the speaker piece into your ear 11 Pairing to Bluetooth Phone Pairing Procedure Pairing is a Bluetooth function that enables Bluetooth devices to remain permanently linked to each other. By pairing devices, you only need to authenticate and authorize communication between your devices once. During the pairing procedure, a PIN code is required for secure authentication. Thereafter, communication between your two Bluetooth devices is done automatically without requiring authentication or confirmation. For the procedure below, you will need to know how to use your cell phone’s Bluetooth feature for discovering, connecting, and pairing to other Bluetooth devices. If you’re not sure how to do this, please consult your cell phone user manual. To pair the IOGEAR Bluetooth headset with your Bluetooth phone, follow the procedure below: 1. Turn headset ON (see page 8 under Introduction) 2. Press and hold the Volume-Up (+) button for more than four (4) seconds; the red LED will turn ON and the blue LED will start rapidly flashing; the headset is now in pairing mode. NOTE: If only the blue LED is on, the headset is in stand-by mode; repeat the step again and make sure 12 Pairing to Bluetooth Phone the red LED is on and blue LED is blinking. The Bluetooth headset will remain in pairing mode for approximately five minutes. If no pairing takes place during that time interval, it will switch to stand-by mode. 3. Follow your cell phone’s instructions to search for Bluetooth devices. The IOGEAR Bluetooth headset will show up as “IOGEAR BT Headset.” If the head...