Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
16 Using Flash ...................................................................................................... 16 Using Hold ........................................................................................................ 17 Using Tone Service on a Pulse Line ................................................................. 17 Memory Dialing ................................................................................................ 17 Storing a Number In Memory ..................................................................... 17 Entering a Pause in a Memory Number ..................................................... 18 Dialing a Memory Number ......................................................................... 18 Chain-Dialing ............................................................................................. 19 Testing Stored Emergency Numbers ......................................................... 19 Using the Intercom ........................................................................................... 19 From the Base ........................................................................................... 19 From the Headset ...................................................................................... 19 Troubleshooting .................................................................................................... 20 Care ........................................................................................................................ 22 The FCC Wants You to Know ........................................................................... 22 Lightning ........................................................................................................... 22 5 43-007.fm Page 6 Wednesday, March 22, 2000 11:24 AM INSTALLATION SELECTING A LOCATION You can place the ET-007 on a desk or table, mount it on a standard wall plate, or mount it directly on a wall. Choose a location that is: • near an AC outlet • near a modular telephone line jack • out of the way of normal activities Note: Your ET-007 connects directly to a modular telephone line jack. If your phone line jack is not a modular jack, you can update the wiring yourself, using jacks and adapters available at your local RadioShack store. Or, you can let the phone company update the wiring for you. Cautions: ! You must use a Class 2 power source that supplies 9V DC and delivers at least 300 mA. Its center tip must be set to positive and its plug must fit the ET007' s 9V DC 300mA jack. The supplied adapter meets these specifications. Using an adapter that does not meet these specifications could damage the ET-007 or the adapter. • Always connect the AC adapter to the ET-007 before you connect it to AC power. When you finish, disconnect the adapter from AC power before you disconnect it from the ET007. CONNECTING THE HANDSET Plug the supplied coiled handset cord into the jacks on the handset and the left side of the corded phone. Note: Your local RadioShack store sells a variety of longer coiled handset cords, which are especially useful when you mount the phone on the wall. PLACING THE BASE TELEPHONE ON A DESK 300mA 1. Plug one end of the supplied modular cord into the TEL. LINE jack on the back of the base. 2. Plug the modular cord's other end into a modular phone line jack. 3. Plug the supplied AC adapter's barrel plug into the 9V DC 300mA on the back of the phone. Then plug the adapter into a standard AC outlet. 6 43-007.fm Page 7 Wednesday, March 22, 2000 11:24 AM 4. Route the adapter's cord through the strain relief slot on the bottom of the phone. 5. Lift the base telephone's antenna to a vertical position. CONNECTING THE HEADSET CHARGER, WIRELESS HEADSET AND INFRARED REMOTE DIAL CARD Wireless Headset Headset Charger To connect the headset charger, connect the headset charger’s built-in AC cord to the AC outlet. The plug fits only one way. Follow these steps to connect the wireless headset: 1. Slide open the battery compartment cover on the left side of the headset. 2. Install the supplied rechargeable nickel-metal hydride (Ni-MH) battery pack in the headset’s battery compartment with the battery contact points down. Battery Pack Important: You must install the battery pack and fully charge it before you can use the headset (see “Charging the Battery Pack” on Page 10). 3. Replace the cover. 4. Place the headset on the headset charger. The charging indicator on the headset lights red, then flashes slowly when the battery pack is fully charged. Notes: • The charging indicator lights when the headset is on the headset charger, even if there is no battery pack in the headset. Be sure the battery pack is inserted before charging. 7 43-007.fm Page 8 Wednesday, March 22, 2000 11:24 AM • The INTERCOM and HOLD indicators on the corded phone stop flashing after the headset charger and wireless headset are connected, even when there is no battery pack in the headset. If they flash, move ...