Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
43-1236 Multi-Phone Recording Control Your RadioShack Multi-Phone Recording Control helps you automatically record all your phone calls. It is compact, simple to connect, and requires no batteries. This control can be used with most phones and with any cassette recorder that has microphone and remote jacks. Your control has been tested and found to comply with all applicable UL and FCC standards. WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture. CAUTION !RISK OF ELECTRIC SHOCK. DO NOT OPEN. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product’s case. Important: It is illegal in some states to record a conversation without the consent of all parties to the conversation, including the phone company. Check the laws in your area before using the control. Note: The control is not designed for use with multi-line phones. READ THIS BEFORE INSTALLATION We have designed this control to conform to federal regulations and you can connect it to most telephone lines. However, each device that you connect to the phone line draws power from the phone line. We refer to this power draw as the device’s ringer equivalence number, or REN. The REN is on the bottom of your control. If you are using more than one device on the line, add up all the RENs. If the total is more than five, your phone might not ring. In rural areas, a total REN of three might impair ringer operation. If ringer operation is impaired, disconnect one of the devices from the line. ! This symbol is intended to inform you that important operating and maintenance instructions are included in the literature accompanying this product. © 1996, 1998 Tandy Corporation. All Rights Reserved. RadioShack is a registered trademark used by Tandy Corporation. 43-1236.fm Page 2 Wednesday, August 18, 1999 9:05 AM FCC STATEMENT Your control complies with Part 68 of FCC Rules. You must, upon request, provide the FCC registration number and the REN to your phone company. Both numbers appear on the bottom of the control. Note: You must not connect your control to: • Coin-operated systems • Party-line systems • Most electronic key phone systems This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CONNECTING THE RECORDING CONTROL Note: This control connects directly to a modular telephone line jack. If your telephone wiring does not have a modular jack, you can update the wiring yourself or have the phone company update the wiring for you. • RadioShack stores sell jacks and adapters to convert older wiring methods to modular wiring. • The USOC number of the jack to be installed is RJ11C (or RJ11W for a wall plate jack). 1. Plug the control’s modular phone cord into a modular phone jack. Note: To connect both a phone and the control to the same phone line jack, first plug a modular duplex jack (such as RadioShack Cat. No. 279-357) into the phone jack. Then plug the control and phone line cords into the duplex jack. 2. Connect the control’s larger plug to your recorder’s microphone jack. Connect the smaller plug to your recorder’s remote jack. 3. If you are using a tape recorder that requires four 1.5V batteries (could be AA, AAA, C, or D), set the control’s 6V/3V switch to 6V. If you are using a tape recorder that requires two 1.5V batteries, set the control’s 6V/3V switch to 3V. Illustration SETTING UP THE RECORDING CONTROL 1. Set the control’s RECORD/PLAYBACK switch to RECORD. 2 43-1236.fm Page 3 Wednesday, August 18, 1999 9:05 AM Illustration 2. The A/B switch lets you set the switch polarity to match that of the tape recorder used with the control. Set A/B to the position that stops recording when you are not using the phone line. Start by setting A/B to A. Then put a cassette tape into the recorder and press the record button. If the tape moves, set A/B to B. If the tape did not move, leave A/B set to A. Illustration 3. To test the control, lift the handset of any phone on the telephone line. The tape should start moving and recording should begin. Hang up the phone. The tape should stop. USING THE RECORDING CONTROL To record a call, set RECORD/PLAYBACK to RECORD. The recorder automatically records all phone calls you make and receive. 3 To stop recording, stop the recorder. To play the cassette tape, set RECORD/PLAYBACK to PLAYBACK and follow the instructions in your tape recorder’s owner’s manual to rewind and play the tape. CARE AND MAINTENANCE To enjoy your RadioShack Multi- Phone Recording C...