Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Light and comfortable to wear. Durable construction. Battery low warning beep. This User Guide provides you with all the information you need to get the most from your headset. You must first set up your headset before you can use it. Just follow the simple instructions on the next few pages. Got everything? BT Prelude 20 Headset BT Prelude 20 Earpiece and Microphone Charging unit BT Prelude 20 Headset – Edition 2 – 14.06.04 – 6170 6170 BT Prelude 20 UG [2] 14/6/04 3:31 pm Page 3 Getting started 3 Range Once paired with a Bluetooth phone/device, your BT Prelude 20 Headset has a range of 10 metres. If you go outside this range, the signal between the phone and headset will be lost. Charge the headset battery for 21/2 hours 1. Plug the Charger into your BT Prelude 20 Headset. Plug the other end into the mains power and switch on. 2. During charging the red charger light comes on. Charge for at least 21/2 hours or until the red charging light goes off. Talk/Standby time Under ideal conditions, a fully charged battery will give up to 5 hours talktime or up to 180 hours standby. Battery low warning When the battery needs recharging, you will hear a warning beep on the headset every 40 seconds and the indicator light will flash RED. Battery performance Your headset has a rechargeable Li-Polymer battery. Running the battery right down at least once a month will help them it as long as possible. The charge capacity of a rechargeable battery will reduce with time as it wears out, so reducing the talk/standby time of the headset. Eventually it will need to be replaced. New batteries can be obtained from withandwithoutwires.com or call 0870 240 5522. BT Prelude 20 Headset – Edition 2 – 14.06.04 – 6170 6170 BT Prelude 20 UG [2] 14/6/04 3:31 pm Page 4 4 Getting started Get to know your headset On/Off Switches headset on/off. Indicator light Volume up Increase earphone volume during a call. Charging socket Volume down Decrease earphone volume during a call. Clip Earphone Microphone Earphone socket Lets you clip the headset unit to a shirt or blouse. 6170 BT Prelude 20 UG [2] 14/6/04 3:32 pm Page 5 Getting started 5 BT Prelude 20 Headset – Edition 2 – 14.06.04 – 6170 Before using your BT Prelude Headset, you must ‘pair’ it to a Bluetooth phone or other compatible device. 1. Make sure your BT Prelude headset battery is fully charged. 2. Make sure your headset is switched off. 3. Press and hold the button until the light flashes green and red alternately (after about 6 seconds). Your headset is now in pairing mode and will remain so for 1 minute. 4. If pairing with a BT Prelude phone: The BT Prelude phone is always in Bluetooth reception mode. The phone’s screen should list the BT Prelude 20 Headset as TECOM BT3061. Pairing 8888888888888888 20 03 09 : 22 6 6170 BT Prelude 20 UG [2] 14/6/04 4:07 pm Page 6 BT Prelude 20 Headset – Edition 2 – 14.06.04 – 6170 6170 BT Prelude 20 UG [2] 14/6/04 3:34 pm Page 7 Pairing 7 If pairing with another phone: Follow the steps shown in your Bluetooth phone’s user guide to start Bluetooth pairing. On the phone, confirm pairing. 5. If your phone asks for a passkey or PIN, enter 1111 (this is the default passkey for your BT Prelude 20) and confirm. 6. When pairing is successful, your headset will go to standby and the green standby indicator light will flash every 3 seconds. BT Prelude 20 Headset – Edition 2 – 14.06.04 – 6170 6170 BT Prelude 20 UG [2] 14/6/04 3:34 pm Page 8 Using the headset 8 Important Before using your headset, it must be paired with a Bluetooth phone/device. You must also be within 10 metres of the paired Bluetooth phone/device. Connecting with other Bluetooth devices Once paired and switched on, your BT Prelude 20 headset will automatically link with your BT Prelude phone when it is within range. However, with some other phones/devices you may need to establish the link each time. A link is usually established either by: Selecting Establish Bluetooth Connection (or similar) on your Bluetooth phone/device. Or Pressing the headset’s button when it is in standby. If the link is successful, the green indicator light will flash rapidly every 3 seconds. Switch headset on 1. Press and hold on the headset until the green light starts flashing quickly and the headset beeps. The headset is switched on and in standby mode. BT Prelude 20 Headset – Edition 2 – 14.06.04 – 6170 6170 BT Prelude 20 UG [2] 14/6/04 3:34 pm Page 9 Using the headset 9 Switch headset off 1. Press and hold on the headset until the red light flashes and the headset beeps. Make a call 1. Use your phone to dial the number as normal. When the line is open, you will hear the call through your headset. Answer a call 1. When the phone rings: press on your headset to answer the call. Adjust volume 1. During a call: press to increase or to decrease the earpiece volume. BT Prelude 20 Headset – Edition 2 – 14.06.04 – 6170 6170 BT Prelude 20 UG [2] 14/6/04 3:34 pm Page 10 10 Using the headset Secrecy During a call, you can ...