CHAIN SHARPENING Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener. IGNITION TIMING Ignition timing is fixed and nonadjustable. SPARK PLUG The spark plug should be replaced each year to ensure the engine starts easier and runs better. S Loosen 3 screws on cylinder cover. S Remove the cylinder cover. S Pull off the spark plug boot. S Remove spark plug from cylinder and dis card. S Replace with Champion R

316.350850 with CAUTION: Before using this • SAFETY product, read this manual and • ASSEMBLY follow all safety rules and oper• OPERATION ating instructions. • MAINTENANCE • PARTS LIST Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Visit our website: 9096-31B206(2) date(08/06) TABLE OF CONTENTS TABLE OF CONTENTS Warranty Page 2 Maintenance and Repair Pages 15 - 21 Safety Rules Pages 3 - 8 Troubleshooting Page 22 Oil and Fuel Information Page 9 Specifications Page 23 Starting/Stopping I

Please do not return unit to retailer. • 1-800-554-6723 Instruction Manual Manual de Instrucciones Manuel d'lnstructions 1950 / 1975 / 2050 / 2055 / 2075 2150 / 2155 / 2175 / 2350 / 2375 2050WT / 2150PR For Occasional Use Only & & WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury. ADVERTENCIA: Lea et manual de instrucciones y siga todas Ias advertencias e enstrucciones de seguridad. Et no hacerlo puede re

S Pull-In can occur when the moving chain contacts a foreign object in the wood in the cut along the bottom of the guide bar and the saw chain is suddenly stopped. This sudden stopping pulls the saw forward and away from the operator and could easily cause the operator to lose control of the saw. 4 Avoid Pinch--Kickback: S Be extremely aware of situations or obstructions that can cause material to pinch the top of or otherwise stop the chain. S Do not cut more than one log at a time. S Do not tw

Low- -- Kickback Chain has met kickback performance requirements when tested on a representative sample of chain saws below 3.8 cubic inch displacement specified in ANSI B175.1. Contoured Depth Gauge Elongated Guard Link Deflects kickback force and allows wood to gradually ride into cutter Can Obstruct Material Low---KickbackChainNot a Low---Kickback Chain S Front Hand Guard, designed to reduce the chance of your left hand contacting the chain if your hand slips off the front handlebar. S Positi

Failure to follow all Safety Rules and Precautions can result in serious injury. If situations occur which are not covered in this manual, use care and good judgement. If you need 5 assistance, contact your Authorized Service Dealer or call 1-800- --554- --6723. ASSEMBLY Protective gloves (not provided) should be worn during assembly. ATTACHING THE BAR & CHAIN (If not already attached) WARNING: If received assembled, repeat all steps to ensure your saw is properly assembled and all fasteners are

Use a screwdriver to move chain sure engine stops; then restart engine and continue. around guide bar to ensure kinks do not exist. The chain should rotate freeSy. 14 Guide Ear _ J Screwdriver Adjusting Wheel Knob 2. Lift lever on bar knob and turn counterclockwise 1 turn to loosen bar clamp. CRAF LOOSEN 3. Turn adjusting wheel (downward direction) to tension chain until chain solidly contacts bottom of guide bar rail. Lift tip of guide bar while adjusting tension. Tighten Loosen chain chain Adj

CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service dealer for replacement of damaged or worn parts. NOTE: It is normal for a small amount of oil to appear under the saw after engine stops. Do not confuse this with a leaking oil tank. S ON/STOP Switch - --Ensure ON/STOP switch functions properly by moving the switch to the STOP position. Make sure engine stops; then restart engine and continue. S Fuel Tank - --Do not use saw if fuel tank shows signs of damage or leaks. S Oil Tank - --D

Guarantee & Guarantee Policy If any part is found to be defective due to faulty manufacture within the guarantee period, Electrolux Outdoor Products, through its Authorised Service Repairers will effect the repair or replacement to the customer free of charge providing: (a) The fault is reported directly to the Authorised Repairer. (b) Proof of purchase is provided. (c) The fault is not caused by misuse, neglect or faulty adjustment by the user. (d) The failure has not occurred through fair wear

Remove small limbs with one cut. S Keep the tree between you and the chain. S Remove larger branches with the cutting techniques described in BUCKING WITHOUT A SUPPORT. S Always use an overcut to cut small and freely hanging limbs. Undercutting could cause limbs to fall and pinch the saw. PRUNING WARNING: Limit pruning to limbs shoulder height or below. Do not cut if branches are higher than your shoulder. Get a professional to do the job. S Make your first cut 1/3 of the way through the bottom