Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
ting, besurethe and bar are being properly lubricated, chain / A B Fig. 17 14 Fig. 20 IV]AmNTENANCE SCHEDULE NOTE: Maintenance, repHacement, or repair of the emission controH devices and system may be per- Perform these required maintenance procedures at the fre formed by a Sears or other qualified service deabr. quency stated in the tame. These procedures shouHd aBo be a part of any seasonaH tune-up. NOTE: Maintenance, repHacement, or repair of the emission controH devices and system may onHybe IAIAO_|M_ld'_, To prevent serious performed by a Sears or other qualified service • injury, never performdeabr. maintenance or repairs with unit running. AJways service and repair a cooH unit. Disconnect the spark pUugwire to ensure that the unit cannot start. A good preventive maintenance program of reguBr inspection and care will increase life and improve performance of your chain saw. This maintenance checklist is a guide for such a program. Cleaning, adjustment, and part replacement may be required, under certain conditions, at more frequent intervals than those indicated. CUSTOMER RESPONSiBiLiTY MAINTENANCE CHECKLIST HOURS OF OPERAEACH USE TION ............................................................................................................................ ...................................LT.,E.M...B.E.E.O....R..E...E...A..C..H....U...,S..E.!.0..............................2..0.. CHECK FOR LOOSE NUTS/BOLTS SCREWS/ ............................................................................... _ ............................................................................... A .......................................... _ ................................. m................................. J CLEAN OR REPLACE THE AIR FILTER REPLACE REPLACEREPLACE OIL / FUEL FILTER SPARK PLUG CLEAN, INSPECT SPARK PLUG ARRESTOR SCREEN / MUFFLER CHECK GUIDE BAR AND CHAIN OIL, ..L!_.L_°..s.._ ..................................................................................................................................................................................................................................................... CLEAN UNIT AND INSPECT DECALS CHECK CHAIN BRAKE@ COMPONENTS ................................................................................................................................................................ t............................................................................................................. CLEAN GUIDE BAR GROOVE CHECK FOR DAMAGED / WORN PARTS CHECK CHAIN TENSION CHECK CHAIN SHARPNESS LUBRICATE SPROCKET TIP CHECK FUEL MIXTURE ................................................................................................................................................................ k ............................................................................................................. 15 REMOVING GUIDE BAR AND CHAIN . To ensure the bar and • chain receive oil, ONLY USE THE ORiGiNAL STYLE BAR with the oil passage hob (A) as illustrated in Fig. 21. NOTE: Always wear heavy gloves when handling the saw chain. 1, Make sure the Chain Brake@ lever is pulled back into the DISENGAGED position (Fig. 21). Remove bar retaining nuts with supplied multi-purpose tool (Fig. 22). 2, Remove chain brake cover (C, Fig. 22) and outer guide bar plate 0, Fig. 27) by pulling straight out (Fig. 22). 3, Slide bar off the two bar bolts and remove chain (Fig. 23), A REPLACING GUIDE BAR AND CHAIN Always use protective] WARNING: gloves when handling / the saw chain. J ! 1. Spread chain out in a loop with cutting edges (E) pointing CLOCKWISE around loop (Fig. 24}. 2. Slip the chain around the sprocket (F) behind the clutch (G). Make sure the links fit between the sprocket teeth (Fig. 25). 3. Place the slotted end of the guide bar over the two bar bolts (D, Fig. 23). Be sure adjusting tang (J, Fig. 23) is in lower adjusting hob of the bar. 4. Guide the drive links into the groove (H) and around the end of the bar (Fig. 25). 5. The chain will be tight so you will have to rotate the clutch clockwise by hand so the chain engages the bar sprocket. 6. Replace the outer guide bar plate (J)so the bent edges (top and bottom) are directed away from the chain (Fig. 27). 7. Install the Chain Brake@ cover (Fig. 27). Make sure the chain does not slip off of the bar. Install the 2 bar retaining nuts hand tight and follow instructions in Saw Chain Tension Adjustment. NOTE: The guide bar retaining nuts are installed only hand tight at this point because saw chain adjustment is required. Follow instructions in Saw Chain Tension AdJustment. Fig. 22 Fig. 23 Fig. 25 B Fig. 27 16 SAW CHAroN TENSION ADJUSTMENT WARNmNG: Ak,vaysuse protective gloveswhen handling thesaw chain_ Proper tension of saw chain is extremely important and must be checked before starting, as well as during any cutting operation, Taking the time to make needed adjustments to the saw chain will result in improved cutting perform...
Эта инструкция также подходит к моделям:Бензо и электропилы - 316.35084 (3.28 mb)
Бензо и электропилы - 316.35084 (3.28 mb)
Бензо и электропилы - 316.35084 (3.28 mb)