Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Do not wear loose-fitting clothing, which could be drawn into the engine or catch the chain or undergrowth. Wear overalls, jeans, or leggings made of cut-resistant material or ones that contain cut-resistant inserts. Secure hair so that it is above shoulder level. ¦ ¦¦¦¦¦Wear non-slip safety footwear and heavy-duty gloves to improve your grip and to protect your hands. ¦ ¦¦¦¦¦Wear eye (E), hearing (F), and head (G) protection when operating this equipment. PROPER GRIP ON HANDLES See Figures 17 and 18. Refer to “Specific Safety Rules – Proper Clothing For Safety” earlier in this manual for appropriate safety equipment. ¦ ¦¦¦¦¦Wear non-slip gloves for maximum grip and protection. CAUTION: Failure to release partial throttle when chain brake lever is in the brake position will result in serious damage to the unit. Never squeeze and hold the throttle trigger while the chain brake is in the brake position. UK- Page 10 OPERATION ¦¦¦¦¦Maintain a proper grip on the saw whenever the engine is running. The fingers should encircle the handle and the thumb be wrapped under the handlebar. This grip is least likely to be broken (by a kick-back or other sudden reaction of the saw). Any grip in which the thumb and fingers are on the same side of the handle is dangerous because a slight kick of the saw can cause loss of control. WARNING: DO NOT operate the throttle trigger with your left hand and hold the front handle with your right hand. Never allow any part of your body to be in the chain line while operating a saw. 2. Accelerate the engine to full throttle just before entering the cut by squeezing the throttle trigger. 3. Begin cutting with the saw against the log. 4. Keep the engine at full throttle the entire time you are cutting. 5. Allow the chain to cut for you; exert only light downward pressure. Forcing the cut could result in damage to the bar, chain, or engine. 6. Release the throttle trigger as soon as the cut is completed, allowing the engine to idle. Running the saw at full throttle without a cutting load may result in unnecessary wear to the chain, bar, and engine. 7. Do not put pressure on the saw at the end of the cut. WORK AREA PRECAUTIONS See Figure 21. ¦¦¦¦¦Cut only wood or materials made from wood; no sheet metal, no plastics, no masonry, no non-wood building materials. ¦¦¦¦¦Never allow children to operate your saw. Allow no person to use this chainsaw who has not read this operator’s manual or received adequate instructions for the safe and proper use of this chainsaw. ¦¦¦¦¦Keep everyone – helpers, bystanders, children, and animals, a SAFE DISTANCE from the cutting area. During felling operations, the safe distance should be a least twice the height of the largest trees in the felling area. During bucking operations, keep a minimum distance of (15 ft) 4.5 m. between workers. ¦¦¦¦¦Always cut with both feet on solid ground to prevent being pulled off balance. ¦¦¦¦¦Do not cut above chest height as a saw held higher is ¦¦¦¦¦Hold the saw firmly with both hands. Always keep your LEFT HAND on the front handle and your RIGHT HAND on the rear handle so that your body is to the left of the chain line. WARNING: Never use a left-handed (cross-handed) grip or any stance that would place your body or arm across the chain line. OPERATION ¦¦¦¦¦Maintain a proper grip on the saw whenever the engine is running. The fingers should encircle the handle and the thumb be wrapped under the handlebar. This grip is least likely to be broken (by a kick-back or other sudden reaction of the saw). Any grip in which the thumb and fingers are on the same side of the handle is dangerous because a slight kick of the saw can cause loss of control. WARNING: DO NOT operate the throttle trigger with your left hand and hold the front handle with your right hand. Never allow any part of your body to be in the chain line while operating a saw. 2. Accelerate the engine to full throttle just before entering the cut by squeezing the throttle trigger. 3. Begin cutting with the saw against the log. 4. Keep the engine at full throttle the entire time you are cutting. 5. Allow the chain to cut for you; exert only light downward pressure. Forcing the cut could result in damage to the bar, chain, or engine. 6. Release the throttle trigger as soon as the cut is completed, allowing the engine to idle. Running the saw at full throttle without a cutting load may result in unnecessary wear to the chain, bar, and engine. 7. Do not put pressure on the saw at the end of the cut. WORK AREA PRECAUTIONS See Figure 21. ¦¦¦¦¦Cut only wood or materials made from wood; no sheet metal, no plastics, no masonry, no non-wood building materials. ¦¦¦¦¦Never allow children to operate your saw. Allow no person to use this chainsaw who has not read this operator’s manual or received adequate instructions for the safe and proper use of this chainsaw. ¦¦¦¦¦Keep everyone – helpers, bystanders, children, and animals, a SAFE DISTANCE from the cutting area. During felling...
Эта инструкция также подходит к моделям:Бензо и электропилы - CSP4518 - UT74125D (657.9 kb)
Бензо и электропилы - CSP4520 - UT74127D (657.9 kb)