Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
2. Checkallitemsforanyshippingdamage.Ifyoufind any damage or if any parts are missing, promptly inform dealer where you bought chain saw. CHAIN SAW NAMES AND TERMS Bucking Process of cutting a felled tree or log into lengths. Felling Process of cutting down a tree. Felling Cut Final cut when felling a tree. Make this cut on opposite side of tree from notching cut. Front Handle Located at front of saw body. Front Hand Guard Shield between front handle and guide bar. Protects left hand while using saw. Guide Bar Metal bar that extends from saw body. The guide bar supports and guides chain. Guide Bar Nose Tip or end of guide bar. Kickback Quick backward and upward motion of guide bar. Kickback may occur when tip of guide bar touches an object while chain is moving. The guide bar will kick up and back towards operator. Limbing Process of cutting limb(s) from a felled tree. Low-Kickback Chain Chain that reduces chance of kickback as required by ANSI B175.1. Normal Cutting Position Stance used while making bucking and felling cuts. Notching Cut Notch cut in tree that directs fall of tree. Oiler Control System for oiling guide bar and chain. Power Head Chain saw without chain and guide bar. Also known as saw body. Pushback (Kickback, Pinch) Rapid pushback of chain saw. Pushback may occur if chain along top of guide bar is pinched, caught, or contacts a foreign object. Rear Handle Handle located at rear of saw body. Reduced Kickback Guide Bar Guide bar that reduces chance of kickback. Continued 108539 15 CHAIN SAW NAMES AND TERMS Continued Replacement Chain Chain that complies with ANSI B175.1 when used with a specific saw. It may not meet ANSI requirements when used with other saws. Saw Chain (Chain) Loop of chain having cutting teeth for cutting wood. The motor drives chain. The guide bar supports chain. Spiked Bumper (Spike) Pointed teeth at front of saw body beside guide bar. Keep spiked bumper in contact with wood when felling or bucking. It helps maintain position of saw while cutting. Sprocket Toothed wheel that drives chain. Switch Device that completes or interrupts electrical circuit to motor of saw. Switch Linkage This device connects switch to trigger. It moves switch when you squeeze trigger. Switch Lockout Device that reduces accidental starting of saw. Trigger Device that turns saw on and off. Squeezing trigger turns saw on. Releasing trigger turns saw off. Trimming (Pruning) Process of cutting limb(s) from a living tree. Undercut An upward cut from underside of log or limb. This is done while in normal cutting position and cutting with top of guide bar. ASSEMBLY Note: Some models are pre-assembled. Assembly is not needed on these models. See Saw Chain Tension Adjustment, pages 16 and 17. WARNING:Cutting edges on chain are sharp.Use protective gloves when handling chain. IMPORTANT:Do not clamp chain saw in vise during assembly. The plastic hardware bag should include: • two guide bar bolts • two guide bar nuts • one Phillips-head tapping screw 1. Lay chain out flat. 2. Install front hand guard onto saw body. Do this by pressing two mounting stand-outs on hand guard into hex-shaped holes in saw body (see Figure 3). Insert tapping screw through hand guard and into saw handle. Tighten screw firmly. 4. Turn adjusting screw counterclockwise (see Figure 4). Continue to turn adjusting screw until adjusting block is to rear of adjusting plate. 5. Install guide bar onto saw body. Place rear of guide bar between adjusting plate and sprocket support. IMPORTANT: Make sure to insert adjusting block into oval adjusting hole on guide bar. 6. Line up holes on sprocket support with center slot on guide bar and holes in saw body. 7. Insert guide bar bolts through front hand guard, saw body, center slot of guide bar, and sprocket support. Attach guide bar nuts to guide bar bolts. IMPORTANT: Tighten guide bar nuts finger tight only. Make sure adjusting block is in oval adjusting hole on guide bar. 8. Place chain around drive sprocket, then along top groove of guide bar and around guide bar nose. Note: Make sure cutting edges of chain are facing the right direction. Position chain so cutting edges on top of guide bar face guide bar nose (see Figure 3). CAUTION:Do not place chain on saw backwards. If chain is backwards, saw will vibrate badly and will not cut. 9. Adjust saw chain tension. Follow steps under Saw Chain Tension Adjustment, pages 16 and 17. SAW CHAIN TENSION ADJUSTMENT WARNING: Unplug chain saw from power source before adjusting saw chain tension. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. WARNING:Maintainproperchaintension always. A loose chain will increase the risk of kickback. A loose chain may jump out of guide bar groove. This may injure operator and damage chain. A loose chain will cause chain, guide bar, and sprocket to wear rapidly. Note: For pre-assembled models, the saw chain tension is properly set at factory. A new chain will stretch. Ch...
Эта инструкция также подходит к моделям:Бензо и электропилы - 104316-04, 104316-05, 106890-01, 106890-02, 108526-01, 104317, 106821, 106821A (1.01 mb)
Бензо и электропилы - 106890-01 (1.01 mb)