Оценок - 4, средний балл: 4.8
(
)
)
|
Фрагмент инструкции
F. Depress the LOCK/OFF button with your right thumb. Squeeze the trigger with your index finger (Fig. 7). G. While the motor is running, activate the Chain Brake® by rolling your left hand forward against the lever. H. Chain and motor should stop abruptly. If the chain andWARNING: motor fail to stop when the Chain Brake® is engaged, take the saw to the nearest Authorized Service Center. Do not use the saw if the Chain Brake® is not in proper working order. EXTENSION CORDS When using an electric chain saw, plug it into the extension cord only when you are ready to cut wood. Connect the extension cord to a 110/120 voltage outlet. Refer to the Electrical Safety Warnings section. A cord that is hot to CAUTION: the touch is overloaded. Do not operate your WARNING: chain saw in a wet or damp environment. Do not expose the saw to rain, snow or sleet. Moisture will cause short circuits. Replace or repair any damaged or frayed extension cords before using your saw. Keep the cord away from the cutting area and position the cord so that it will not be caught on branches or other objects during cutting. DOUBLE INSULATION WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS. Information Do not use if the cord or plug is damaged. Your appliance is double insulated to help protect against electric shock. Double insulation construction consists of 2 separate “layers” of electrical insulation. Appliances built with this insulation system are not intended to be grounded. As a result, the extension cord used with your appliance can be plugged into any conventional 120 volt electrical outlet. Normal safety precautions must be observed when operating an electrical appliance. The double insulation system is only for added protection against injury resulting from a possible internal electrical insulation failure. Your double WARNING: insulated appliance has no serviceable parts inside. Do not attempt to repair it yourself. For service information, dial 1-800-520-5520. In this double insulated appliance, 2 systems of insulation, instead of grounding, are provided. No grounding means is provided on a double insulated appliance, nor should a means for grounding be added to the appliance. No serviceable parts are inside. A double insulated appliance is marked with the words, “DOUBLE INSULATION” or “DOUBLE INSULATED.” The symbol (square within a square) may also be marked on the appliance. Maintenance 1. Place switch in OFF position and unplug the power supply before the appliance is serviced, cleaned, or maintenance is performed. 2. Keep the air intake clean and air vents free of debris to avoid overheating the motor. 3. Clean with a damp sponge and mild soap. Do not squirt with a water hose or douse with water or other liquids. 4. Inspect the saw chain for proper tension before each use and frequently during cutting. Sharpen as required. 5. Clean the guide bar and bar pad to ensure free path for oil. 6. No motor lubrication is necessary. The motor is equipped with lifetime lubricated bearings. 7. If the saw does not operate, turn switch to OFF position and disconnect the extension cord, first from the power supply, then from the saw. Check the power supply for blown fuses or tripped circuit breakers. If it still does not operate, contact a Product Service Department. Call 1-800-520-520 for more information. Do not attempt to repair it yourself. No serviceable parts are inside. MAINTENANCE AND REPAIR INSTRUCTIONS MAINTENANCE AND REPAIR INSTRUCTIONS GUIDE BAR MAINTENANCE Frequent lubrication of the guide bar is required. Proper maintenance of the guide bar, as explained in this section, is essential to keep your saw in good working condition. Ensure that the WARNING: power cord is disconnected before performing any maintenance on your saw. Sprocket Tip Lubrication The sprocket tip on CAUTION: your new saw has been pre-lubricated at the factory. Failure to lubricate the guide bar sprocket tip as explained below will result in poor performance and seizure, voiding the manufacturer’s warranty. Lubrication of the sprocket tip is recommended after each saw use. Always thoroughly clean guide bar sprocket tip before lubrication. The Lube Gun (optional) is recommended for applying grease to the guide bar sprocket tip. The Lube Gun is equipped with a needle nose tip which is necessary for the efficient application of grease to the sprocket tip. Fig. 28 To lubricate the sprocket tip: 1.Unplug the chain saw from the power source. NOTE: It is not necessary to remove the saw chain tolubricate the guide bar sprocket tip. Lubricationcan be done on the job. Always use WARNING: protective gloves when handling the saw chain. 2. Clean the guide bar sprocket tip. 3. Using the Lube Gun (optional), insert tip of lube gun into the lubrication hole and inject grease until it appears at outside edge of sprocket tip (Fig. 32). 4. Make sure that the Chain Brake® is deactivated. Rotate saw chain by hand. Repeat lubrication procedure until the entire sprocket ti...
Эта инструкция также подходит к моделям:Бензо и электропилы - TB4516CC (28.06 mb)
Бензо и электропилы - TB4516CC (28.06 mb)
Бензо и электропилы - TB4516CC (28.06 mb)
Бензо и электропилы - TB4516CC (28.06 mb)