Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Hold chain saw firmly with both hands when using. For your own safety, please read and follow the safety precautions in this manual before attempting to operate your chain saw. Improper use can cause serious injury. PN 9096-31Q204 Printed in Taiwan INTRODUCTION 1 - GENERAL INFORMATION 2 1 3 4 5 6 7 1012 11 913 14 16 17 20 18 22 23 15 24 25 21 8 19 1-1.GENERAL IDENTIFICATION 1. SAW CHAIN 2. GUIDE BAR 3. SPARK ARRESTER SCREEN 4. CHAIN BRAKE® LEVER /HAND GUARD 5. FRONT HANDLE 6. STARTER HANDLE 7. STOP SWITCH 8. SAFETY TRIGGER 9. REAR HANDLE / BOOT LOOP 10. FUEL TANK CAP 11. OIL TANK CAP 12. STARTER COVER 13. BUCKING SPIKE 14. CHAIN TENSION RING 15. MUFFLER SHIELD 16. SPARK PLUG 17. AIR CLEANER COVER 18. CHOKE LEVER 19. THROTTLE LATCH 20. PRIMER BULB 21. THROTTLE / TRIGGER 22. CHAIN COVER CONTROL BUTTON 23. CHAIN CATCHER 24. SCREWDRIVER/WRENCH 25. CARRY CASE (Available on some models) 1-2. SAFETY FEATURES Numbers preceding the descriptions correspond with the num bers on preceding page to help you locate the safety feature. 1 LOW KICKBACK SAW CHAIN helps significantly reduce kickback, or the intensity of kickback, due to specially designed depth gauges and guard links. 2 GUIDE BAR Reduced kickback guide bar reduces the intensity of kickback. 3 SPARK ARRESTER SCREEN retains carbon and other flammable particles over 0.023 inches (0.6mm) in size from engine exhaust flow. Compliance with local, state and federal laws and/or regulations governing the use of a spark arrester screen is the user’s responsibility. See Safety Precautions for additional information. 4 CHAIN BRAKE® LEVER / HAND GUARD protects the operator’s left hand in the event it slips off the front handle while saw is running. 4 CHAIN BRAKE® is a safety feature designed to reduce the possibility of injury due to kickback by stopping a moving saw chain in milliseconds. It is activated by the CHAIN BRAKE® lever. 7 STOP SWITCH immediately stops the engine when tripped. Stop switch must be pushed to ON position to start or restart engine. 8 SAFETY TRIGGER prevents accidental acceleration of the engine. Throttle trigger (21) cannot be squeezed unless the safety latch is depressed. 23 CHAIN CATCHER reduces the danger of injury in the event saw chain breaks or derails during operation. The chain catcher is designed to intercept a whipping chain. 2 - SAFETY PRECAUTIONS 2 - SAFETY PRECAUTIONS SAFETY PRECAUTIONS FOR CHAIN SAW USERS (ANSI B175.1-2000, Annex C. CAN/CSA-Z62.1-03) 2-1. KICKBACK SAFETY PRECAUTIONS WARNING Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. If bar tip makes contact with something it may cause a lightning-fast reverse reaction, kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw, which could result in serious personal injury. Do not rely exclusively upon the safety devices built into your saw. As a chain saw user, you should take several steps to keep your cutting jobs free from accident or injury. 1. With a basic understanding of kickback, you can reduce or eliminate the element of surprise. Sudden surprise contributes to accidents. 2. Keep a good firm grip on the saw with both hands, the right hand on the rear handle, and the left hand on the front handle, when the engine is running. Use a firm grip with thumbs and fingers encircling the chain saw handles. A firm grip will help you reduce kickback and maintain control of the saw. Don’t let go. 3. Make sure that the area in which you are cutting is free from obstructions. Do not let the nose of the guide bar contact a log, branch, or any other obstruction which could be hit while you are operating the saw. 4. Cut at high engine speeds. 5. Do not overreach or cut above shoulder height. 6. Follow manufacturer’s sharpening and maintenance instructions for the saw chain. 7. Only use replacement bars and chains specified by the manufacturer or the equivalent. NOTE: Low-kickback saw chain is chain that has met the kickback performance requirements of ANSI B175.1-2000 (American National Standard for Power Tools Gasoline- Powered Chain Saws Safety Requirements) when tested on the representative sample of chain saws below 3.8 c.i.d. specified in ANSI B175.1-2000. 2-2. OTHER SAFETY PRECAUTIONS 1. DO NOT operate a chain saw with one hand! Serious injury to the operator, helpers, bystanders, or any combination of these persons may result from one- handed operation. A chain saw is intended for two- handed use. 2. DO NOT operate a chain saw when you are fatigued. 3. Use safety footwear, snug-fitting clothing, protective gloves, and eye, hearing and head protection devices. 4 4. Use caution when handling fuel. Move the chain saw at least 9.1m (30 feet) from the fueling point before starting the engine. 5. DO NOT allow other persons ...