Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
SYMBOL MEANING • SAFETY ALERT SYMBOL Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs. • WARNING - READ OPERATOR'S MANUAL Read the Operator’s Manual(s) and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders. • WEAR EYE, HEARING AND HARDHAT PROTECTION WARNING: Thrown objects and loud noise can cause severe eye injury and hearing loss. Wear eye protection meeting ANSI Z87.1-1989 standards and ear protection when operating this unit. Wear a hard hat. Use a full face shield when needed. • UNLEADED FUEL Always use clean, fresh unleaded fuel. • OIL Refer to operator's manual for the proper type of oil. SYMBOL MEANING • ON/OFF CONTROL ON / START / RUN • ON/OFF CONTROL OFF OR STOP • GUIDE BAR WARNING: Contact of the guide bar tip with any object should be avoided. Tip contact may cause the guide bar to move suddenly upward and backward, which may cause serious injury. • USE BOTH HANDS Always use both hands while operating the chain saw. Never use only one hand to operate the saw. Avoid bar nose contact. This product has been tested at a computed kickback angle (CKA) of no greater than 45 degrees. 6 RULES FOR SAFE OPERATION KNOW YOUR UNIT 5 21 17 22 20 8 19 24 25 26 9 11 18 3 15 1 2 23 4 6 7 10 12 13 14 16 RULES FOR SAFE OPERATION KNOW YOUR UNIT 5 21 17 22 20 8 19 24 25 26 9 11 18 3 15 1 2 23 4 6 7 10 12 13 14 16 CHAIN SAW COMPONENTS 1. GUIDE BAR 2. SAW CHAIN 3. SAW CHAIN ADJUSTMENT SCREW 4. SPARK ARRESTER SCREEN 5. CHAIN BRAKE® LEVER /HAND GUARD 6. FRONT HANDLE 7. STARTER HANDLE 8. SPARK PLUG 9. AIR CLEANER COVER 10. STOP SWITCH 11. SAFETY LATCH 12. OIL TANK CAP 13. STARTER COVER 14. FUEL TANK CAP 15. REAR HANDLE / BOOT LOOP 16. PRIMER BULB 17. BLUE CHOKE LEVER 18. BAR RETAINING NUT 19. THROTTLE / TRIGGER 20. CHAIN CATCHER 21. MUFFLER SHIELD 22. CLUTCH COVER 23. BUCKING SPIKE 24. CLUTCH COVER RETAINING SCREW 25. SCREWDRIVER / WRENCH 26. CARRY CASE (Available on some models) SAFETY FEATURES Numbers preceding the descriptions correspond with the numbers above to help you locate the safety feature. 2 LOW KICKBACK SAW CHAIN helps significantly reduce kickback, or the intensity of kickback, due to specially designed depth gauges and guard links. 4 SPARK ARRESTER SCREEN retains carbon and other flammable particles over 0.023 inches (0.6mm) in size from engine exhaust flow. Compliance with local, state and federal laws and/or regulations governing the use of a spark arrester screen is the user’s responsibility. See Safety Precautions for additional information. 5 CHAIN BRAKE® LEVER / HAND GUARD protects the operator’s left hand in the event it slips off the front handle while saw is running. 5 CHAIN BRAKE® is a safety feature designed to reduce the possibility of injury due to kickback by stopping a moving saw chain in milliseconds. It is activated by the CHAIN BRAKE® lever. 10 STOP SWITCH immediately stops the engine when tripped. Stop switch must be pushed to ON position to start or restart engine. 11 SAFETY LATCH prevents accidental acceleration of the engine. Throttle trigger (19) cannot be squeezed unless the safety latch is depressed. 20 CHAIN CATCHER reduces the danger of injury in the event saw chain breaks or derails during operation. The chain catcher is designed to intercept a whipping chain. 7 RULES FOR SAFE OPERATION RULES FOR SAFE OPERATION KICKBACK SPECIFICS Kickback can lead WARNING: to dangerous loss of control of the chain saw and result in serious or fatal injury to the saw operator or to anyone standing close by. Always be alert. Rotational kickback and pinch-kickback are major chain saw operational dangers and the leading cause of most accidents. Beware of: Rotational Kickback BA AA A = Kickback path B = Kickback reaction zone Fig. 1 KICKBACK SPECIFICS Beware of: Pinch Kickback (The push and pull reactions) A = Pull B = Solid objects C = Push Fig. 2 A B B C KICKBACK may occur when the NOSE or TIP of the guide bar touches an object, or when wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning-fast reverse reaction, kicking the guide bar up and back toward the operator. PINCHING the saw chain along the BOTTOM of the guide bar may PULL the saw forward away from the operator. PINCHING the saw chain along the TOP of the guide bar may PUSH the guide bar rapidly back toward the operator. Any of these reactions may cause you to lose control of the saw, which could result in serious personal injury. 8 OIL AND FUEL INFORMATION OIL AND FUEL INFORMATION OIL AND FUEL MIXING INSTRUCTIONS Old and/or improperly mixed fuel are the main reasons for the unit not running properly. Be sure to use fresh, clean unleaded fuel. Follow the instructions carefully for the proper fuel/oil mixture. Definition of Blended Fuels Today's fuels are often a blend of gasoline and oxygenates such as ethanol, methanol, or MTBE (ether). Alcohol-blended fuel absorbs water...
Эта инструкция также подходит к моделям:Бензо и электропилы - MTD1425NAV (11.89 mb)
Бензо и электропилы - MTD1842AVCC (11.89 mb)