Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Both situations could cause serious injury. • Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with the bar and chain pointing backwards. Fit a guard to the bar before transporting the chain saw or carrying it for any distance. • Never put a chain saw down while the engine is running unless you have it in clear view and the chain brake is on. Switch the engine off before leaving your chain saw for any length of time. Basic cutting technique General • Always use full throttle when cutting! • Reduce the speed to idle after every cut (running the engine for too long at full throttle without any load, i.e. without any resistance from the chain during cutting, can lead to serious engine damage). • Cutting from above = Cutting on the pull stroke. • Cutting from below = Cutting on the push stroke. Cutting on the push stroke increases the risk of kickback. See instructions under the heading How to avoid kickback. Terms Cutting = General term for cutting through wood. Limbing = Cutting branches off a felled tree. Splitting = When the object you are cutting breaks off before the cut is complete. There are five important factors you should consider before making a cut: 1 Make sure the cutting equipment will not jam in the cut. 2 Make sure the object you are cutting will not split. 3 Make sure the chain will not strike the ground or any other object during or after cutting. 4 Is there a risk of kickback? 5 Do the conditions and surrounding terrain affect how safely you can stand and move about? Two factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is supported before and after cutting, and the second is whether it is in tension. English – 19 SAFETY INSTRUCTIONS In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom.You need to support the object so that it will not trap the chain or split during cutting. ! WARNING! If the chain jams in the cut: stop the engine! Don’t try to pull the chain saw free. If you do you may be injured by the chain when the chain saw suddenly breaks free. Use a lever to open up the cut and free the chain saw. The following instructions describe how to handle the commonest situations you are likely to encounter when using a chain saw. Cutting The log is lying on the ground. There is little risk of the chain jamming or the object splitting. However there is a risk that the chain will touch the ground when you finish the cut. Cut all the way through the log from above. Avoid letting the chain touch the ground as you finish the cut. Maintain full throttle but be prepared for what might happen. If it is possible (can you turn the log?) stop cutting about 2/3 of the way through the log. Turn the log and finish the cut from the opposite side. The log is supported at one end. There is a high risk that it will split. Start by cutting from below (about 1/3 of the way through). Finish by cutting from above so that the two cuts meet. The log is supported at both ends. There is a high risk that the chain will jam. Start by cutting from above (about 1/3 of the way through). Finish by cutting from below so that the two cuts meet. Limbing When limbing thick branches you should use the same approach as for cutting. Cut difficult branches piece by piece. 1 2 3 20 – English English – 21 SAFETY INSTRUCTIONS Tree felling technique Safe distance The safe distance between a tree that is to be felled and anyone else working nearby is at least 21/2 tree lengths. Make sure that no-one else is in this ”risk zone” before or during felling. Felling direction The aim is to fell the tree in a position where you can limb and cross-cut the log as easily as possible. You want it to fall on ground where you can stand and move about safely. The main point to avoid is letting the tree fall onto another tree. See instructions under the heading Freeing a tree that has fallen badly. Once you have decided which way you want the tree to fall you must judge which way the tree would fall naturally. Several factors affect this: • Lean of the tree • Bend • Wind direction • Arrangement of branches • Weight of snow You may find you are forced to let the tree fall in its natural direction because it is impossible or dangerous to try to make it fall in the direction you first intended. Another very important factor, which does not affect the felling direction but does affect your safety, is to make sure the tree has no damaged or dead branches that might break off and hit you during felling. Clearing the trunk and preparing your retreat Remove any branches that are in the way. To do this it is best to work from the top down and keep the trunk between you and the chain saw. Never limb above shoulder height. Remove any undergrowth from the base of the tree and check the area for obstacles (stones, branches, holes, etc.) so that you have a clear path of retreat when the t...
Эта инструкция также подходит к моделям:Бензо и электропилы - POWERLITE 50C (2.04 mb)