Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
See the Technical data section to find out which lengths of bar are recommended for your saw. There are methods for felling trees with a diameter larger than the bar length. However these methods involve a much greater risk that the kickback zone of the bar will come into contact with the tree. WARNING! Unless you have special training we advise you not to fell trees with a diameter larger than the bar length of your saw! Limbing ! WARNING! Most kickback accidents happen during limbing! Pay close attention to the position of the kickback zone of the bar when you are limbing branches that are in tension! ! Make sure that you can stand and move about safely.Work on the left side of the trunk. Work as close as possible to the chain saw for maximum control. If possible, let the weight of the chain saw rest on the trunk. Keep the trunk between you and the chain saw as you move along the trunk. Cutting the trunk into logs See instructions under the heading Basic cutting technique. Freeing a tree that has fallen badly Freeing a ”trapped tree” It is very dangerous to remove a trapped tree and there is high accident risk. The safest method is to use a winch. • Tractor-mounted • Portable Cutting trees and branches that are in tension Preparations: Work out which side is in tension and where the point of maximum tension is (i.e. where it would break if it was bent even more). Decide which is the safest way to release the tension and whether you are able to do it safely. In complicated situations the only safe method is to put aside your chain saw and use a winch. General advice: Position yourself so that you will be clear of the tree or branch when the tension is released. Make one or more cuts at or near the point of maximum tension. Make as many cuts of sufficient depth as necessary to reduce the tension and make the tree or branch break at the point of maximum tension. Never cut straight through a tree or branch that is in tension! 22 – English English – 23 WHAT IS WHAT? What is what on the chain saw? 1 Cylinder cover 2 Front handle 3 Front hand guard 4 Starter 5 Chain oil tank 6 Starter handle 7 Adjuster screws, carburettor 8 Choke control/Start throttle lock 9 Rear handle 10 Stop switch (Ignition on/off switch.) 11 Fuel tank 12 Muffler 13 Bar tip sprocket 14 Chain 15 Bar 16 Spike bumper 17 Chain catcher (Catches chain if it jumps or breaks.) 18 Clutch cover 19 Right hand guard (Protects right hand if chain breaks or jumps.) 20 Throttle control 21 Throttle lock (Prevents accidental operation of throttle control.) 22 Decompression valve (CS 2145, CS 2150) 23 Combination spanner 24 Chain tensioning screw 25 Operator’s manual (EPA) 26 Bar guard 27 Oil pump adjustment screw 28 Warning decal ASSEMBLY Tension the chain by turning the chain tensioning screw Fitting the bar and chain clockwise using the combination spanner. The chain should be tensioned until it does not sag from the underside of the bar. ! WARNING! Always wear gloves, when working with the chain, in order to protect your hands from injury. Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. Remove the bar nuts and remove the clutch cover (chain brake). Take off the transportation ring (A). Fit the bar over the bar bolts. Place the bar in its rearmost position. Place the chain over the drive sprocket locate it in the groove on the bar. Begin on the top edge of the bar. Make sure that the edges of the cutting links are facing forward on the top edge of the bar. Fit the clutch cover and locate the chain adjuster pin in the hole in the bar. Check that the drive links of the chain fit correctly over the drive sprocket and that the chain is correctly located in the groove in the bar. Tighten the bar nuts finger tight. The chain is correctly tensioned when it does not sag from the underside of the bar, but can still be turned easily by hand. Hold up the bar tip and tighten the bar nuts with the combination spanner. When fitting a new chain, the chain tension has to be checked frequently until the chain is run-in. Check the chain tension regularly. A correctly tensioned chain ensures good cutting performance and long life. NOTE! Note: If clutch cover is difficult to remove, replace bar nuts, engage brake and rerelease (an audible click will be heard if released properly). 24 – English FUEL HANDLING Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained.When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline...
Эта инструкция также подходит к моделям:Бензо и электропилы - CS 2141 EPA II (2.02 mb)
Бензо и электропилы - CS 2145 EPA II (2.02 mb)