Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
• Use extreme caution when re-entering a previous cut. • Use low-kickback chain and guide bar supplied with this chain saw. Only replace these parts with chains and guide bars listed in this manual. • Never use dull or loose chain. Keep chain sharp and tensioned correctly. Saw Maintenance and Kickback Safety Follow maintenance instructions in this manual. Proper cleaning of saw along with chain and guide bar maintainance can reduce chances of kickback. Inspect and maintain saw after each use. This will increase the service life of your saw. Note: Even with proper sharpening, risk of kickback can increase with each sharpening. PUSHBACK AND PULL-IN Avoid pushback and pull-in. These hazards can cause you to lose control of chain saw. Pushback or pull-in can cause severe injury. Cause Of Pushback and Pull-In Pushback may occur while cutting with top of guide bar. Pushback will force saw back towards you. Pull-in may occur while cutting with bottom of guide bar. Pull-in will force saw in towards wood you are cutting. These hazards can occur if chain is pinched, caught or contacts a non-wood object. The following steps will reduce the risk of pushback or pull-in. • Use both hands to grip saw while saw is running. Use firm grip. Thumbs and fingers must wrap around saw handles. • Do not overreach or cut above shoulder height. • Keep solid footing and balance. • Stand slightly to left side of saw. This keeps your body from being in direct line with chain. • Have saw running at full speed before starting a cut. • When cutting, make sure spike of saw is against wood (pull-in only). See Product Identification, page 4, to locate spike. • Never try cutting through two logs at same time. Only cut one log at a time. •Watch for shifting of log or other forces that may pinch chain. • Use extreme caution when re-entering a previous cut. • Do not twist saw when removing guide bar from undercut. • Use wedges made of plastic, wood, or light alloy (never steel or iron) to hold cut open. Continued 3 HOMELITE EL12 AND EL16 ELECTRIC CHAINSAW SAFETY INFORMATION Continued WARNINGS IMPORTANT: Make certain you read and understand all Safety Warnings on pages 2 through 4. Improper use of this chain saw can cause severe injury or death from fire, electrical shock, body contact with moving chain, or falling wood. MAINTENANCE AND STORAGE OF CHAIN SAW 1. Unplug chain saw from power source • when not in use • before moving from one place to another • before servicing • before changing accessories or attachments 2. Inspect chain saw before and after each use. Check saw closely if guard or other part has been damaged. Check for any damage that may affect operator safety or operation of saw. Check for alignment or binding of moving parts. Check for broken or damaged parts. Do not use chain saw if damage affects safety or operation. Have damage repaired by authorized service center. 3. Maintain chain saw with care. • Never expose saw to rain. • Keep chain sharp, clean, and lubricated. • Follow steps outlined in this manual to sharpen chain. •Keep handles dry, clean, and free of oil. • Keep all screws and nuts tight. • Inspect power cord often. If damaged, have repaired by authorized service center. • Never carry chain saw by power cord. • Never yank power cord to unplug it. • Keep power cord from heat, oil, and sharp edges. • Inspect extension cords often and replace if damaged. 4. When servicing, use only identical replacement parts. UNPACKING 5. Always store chain saw 1. Remove all items from carton. • in a high or locked place, out of children’s reach 2. Check all items for any shipping dam• in a dry place age. If you find any damage or if any • in a carrying case or with scabbard parts are missing, promptly inform over guide bar dealer where you bought chain saw. Keep this manual for reference. It is your guide to safe and proper operation of this chain saw. PRODUCT IDENTIFICATION Front Hand Power Cord Rear Hand Guard Rear Handle Guard Guide Bar Spike Saw Chain Scabbard Safe•T•Tip® Anti-Kickback Device Oil Level Sight Hole Oil Cap TriggerSwitch Lockout Motor Housing (located on saw body, hidden by front handle) Front Handle Figure 2 - Electric Chain Saw 4 OWNER’S MANUAL CHAIN SAW NAMES AND TERMS Bucking Process of cutting a felled tree or log into lengths. Felling Process of cutting down a tree. Felling Cut Final cut when felling a tree. Make this cut on opposite side of tree from notching cut. Front Handle Located at front of saw body. Front Hand Guard Shield between front handle and guide bar. Protects left hand while using saw. Guide Bar Metal bar that extends from saw body. The guide bar supports and guides chain. Guide Bar Nose Tip or end of guide bar. Kickback Quick backward and upward motion of guide bar. Kickback may occur when tip of guide bar touches an object while chain is moving. The guide bar will kick up and back towards operator. Limbing Process of cutting limb(s) from a felled tree. Low-Kickback Chain Chain that reduces chanc...
Эта инструкция также подходит к моделям:Бензо и электропилы - EL12 (912.08 kb)