Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Serious burns may occur if contact is made with the muffler. WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with hearing and head protection. Failure to do so could result in objects being thrown into your eyes and other possible serious injuries. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury. APPLICATIONS You may use this product for the purposes listed below: . Basic limbing, felling, and bucking . Removing buttress roots WARNING: Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting the engine. DO NOT SMOKE and stay away from open flames or sparks. Failure to safely handle fuel could result in serious personal injury. FUEL AND REFUELING HANDLING THE FUEL SAFELY WARNING: Check for fuel leaks. A leaking fuel cap is a fire hazard and must be replaced immediately. If you find any leaks, correct the problem before using the product. Failure to do so could result in a fire that could cause serious personal injury. n Always handle fuel with care; it is highly flammable. n Always refuel outdoors and do not inhale fuel vapors. n Do not let gasoline or lubricant come in contact with skin. n Keep gasoline and lubricant away from the eyes. If gasoline or lubricant comes in contact with the eyes, wash them immediately with clean water. If irritation is still present, see a doctor immediately. n Clean up spilled fuel immediately. Refer to Refueling in the Specific Safety Rules section of this manual for additional safety information. MIXING THE FUEL n This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded gasoline and 2-cycle engine lubricant in a clean container approved for gasoline. n This engine is certified to operate on unleaded gasoline intended for automotive use with an octane rating of 87 [(R + M) / 2] or higher. ¦n Do not use any type of pre-mixed gasoline/lubricant from fuel service stations, this includes the pre-mixed gasoline/lubricant intended for use in mopeds, motorcycles, etc. ¦n Use a high quality 2-cycle self-mixing lubricant for air-cooled engines. Do not use automotive lubricant or 2-cycle outboard lubricant. ¦n Mix 2% lubricant into the gasoline. This is a 50:1 ratio. n Mix the fuel thoroughly and each time before fueling. ¦n Mix in small quantities. Do not mix quantities larger than usable in a 30-day period. A 2-cycle lubricant containing a fuel stabilizer is recommended. PREMIUM EXACT MIX™ (50:1) GASOLINE LUBRICANT 1 Gallon (US) 2.6 oz. 1 Liter 20 cc (20 ml) OPERATION OXYGENATED FUELS DO NOT USE E85 FUEL. IT WILL VOID YOUR WARRANTY. NOTE: Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates stated previously are not covered under warranty. Ethanol. Gasoline containing up to 10% ethanol by volume (commonly referred to as E10) is acceptable. E85 is not. OPERATION FILLING THE FUEL TANK See Figure 2. n Clean the surface around the fuel cap to prevent contamination. n Loosen the fuel cap slowly, by turning counterclockwise. n Carefully pour the fuel mixture into the tank. Avoid spillage. n Prior to replacing the fuel cap, clean and inspect the gasket. n Immediately replace the fuel cap and hand tighten, by turning clockwise. Wipe up any fuel spillage. n Move at least 30 ft. away from refueling area before starting the product. NOTE: It is normal for the engine to emit smoke during and after the first use. 50:1GASOLINE& LUBRICANT MIX Fig. 2 ADDING BAR AND CHAIN LUBRICANT See Figure 3. Use HOMELITE Bar and Chain Lubricant. It is designed for chains and chain oilers, and is formulated to perform over a wide temperature range with no dilution required. Chain saw should use approximately one tank of lubricant per tank of fuel. NOTE: Do not use dirty, used, or otherwise contaminated lubricants. Damage may occur to the oil pump, bar, or chain. n Carefully pour the bar and chain lubricant into the oil tank. n Fill the oil tank every time you fuel the engine. OPERATING THE CHAIN BRAKE See Figures 4 - 5. Check the operating condition of the chain brake prior to each use. n Engage the chain brake by rotating your left hand around the front handle, allowing the back of your hand to push the chain brake lever/hand guard toward the bar while the chain is rotating rapidly. Be sure to maintain both hands on the saw handles at all times. n Reset the chain brake back into the RUN position by grasping the top of the chain brake lever/hand guard and pulling toward the front handle until you hear a click. WARNING: If the chain brake does not stop the chain immediately, or if the chain brake will not stay in the run position without assistance, take the saw to an authorized service...
Эта инструкция также подходит к моделям:Бензо и электропилы - UT10548 (23.62 mb)
Бензо и электропилы - UT10568 (23.62 mb)