Оценок - 5, средний балл: 4.4
(
)
)
|
Фрагмент инструкции
For this reason the various cuts must be performed with great precision. When cutting operations are completed the tree will begin to fall. Where necessary help tree fall using wedges or felling levers . Limbing Once the tree has been felled, the trunk must be limbed: in other words, the branches are removed from the trunk. Do not underestimate this operation because the large majority of kickback accidents occur during this stage. For this reason pay close attention to the position of the bar nose during cutting operations and always work on the left hand side of the trunk. I. ENVIRONMENTAL INFORMATION This section contains information useful for maintaining the characteristic of ecocompatibility included in the origin design of the machine, and as regards proper use and disposal of chain oil DESIGN In the design stage, care was taken to develop an engine with reduced consumption and low emission of noise. USE OF THE MACHINE The operations of filling the oil tank should be carried out in such a way as to avoid spilling oil and contaminating the soil and the environment. DISPOSAL Do not dispose inappropriately of the machine when it is no longer usable. Deliver it to an authorized organization for proper disposal in compliance with the regulation in force. ENGLISH - 10 M. TROUBLESHOOTING TABLE Motor does not start Motor turns with difficulty or loses power The machine starts but does not cut properly Motor turns improperly or at reduced speeds Braking devices do not stop the chain properly Make sure the main line is powered ..• • • • • Make sure the machine is properly plugged in ..• • • • • Make sure your cable/ext. cord is not damaged ..• • • • • Make sure that chain brake is not activated ..• • • • • Check that chain is properly assembled • ..• ..• • • Check chain lubrification as in chapters F and G • • ..• • • Make sure that the chain is sharp • • ..• • • Contact your authorised centre ..• ..• • ..• ..• ENGLISH – 11 N. DECLARATION OF CONFORMITY The undersigned, authorized by E.O.P.I., declares that the following products model: type ES15, ES 15/1, ES 15/2, ES16, ES 16/1, ES18 starting from 2004 onwards, manufactured by E.O.P.I., Valmadrera, Italy, comply with European Directive: 98/37/EEC (Machine Directive), 93/68/EEC (EEC Marking Directive) & 89/336/CEE (Electromagnetic Compatibility Devices), directive 2000/14/EEC (Enclosure V). Valmadrera, 19/05/2004 Pino Todero (Technical Manager) Electrolux Outdoor Products Italy S.p.A. Via Como 72, 23868 Valmadrera (Lecco) ITALIA O. Technical Data Type: ES 15 ES 16 ES 18 Dry weight (Kg) 3,5 3,5 3,5 Oil tank volume (cm3) 200 200 150 Bar length (cm/inches) 30/12” 35/14’’ 40/16” Chain MPG370GLX 91VJ Chain pitch (inches) 8,25/0,325” 8,25/0,325” 8,25/0,325” Vibration 3/8 3/8 3/8 Front handle (m/s2) (ISO 7505) 3,5 3,5 1,96 Rear handle (m/s2) (ISO 7505) 7,9 7,9 7,30 Measured sound power level LWav dB(A) (ISO 9207) 111,14 111,14 103 Guarateed sound power level Lwav dB(A) (ISO 9207) 113 113 104 Sound pressure level at operator’s ear dB(A) 98 98 94 (EN 27182) Minimum wire cross-section (wires num./mm2) 2x1 2x1 2x1 Maximum cable length (m) 30 30 30 ENGLISH - 12 ...
Эта инструкция также подходит к моделям:Бензо и электропилы - Electramac 312 (3.79 mb)
Бензо и электропилы - Electramac 314 (3.79 mb)
Бензо и электропилы - Electramac 330 (3.79 mb)
Бензо и электропилы - Electramac 416 (3.79 mb)