Оценок - 2, средний балл: 4.5 ( )

Производитель: Remington Power Tools Размер: 2.7 mb Название файла: Язык инструкции:

Make sure saw is running at full speed before starting a cut. Switch Lockout Button Trigger Connect extension cord to power cord and power supply. Use built-in cord hitch or knot method (inset) to secure together. See Extension Cords for correct size. Power Cord Cord Hitch Extension Cord Slot Pour motor oil (see Filling Oil Tank, page 10, for correct oil type) in oil tank (do not use standard bar and chain oil). DO NOT leave oil in tank when not in use. Oil Bottle Oil Squeeze Bulb For complete information concerning your saw and its proper usage, read and understand this owner’s manual thoroughly. QUICK START GUIDE If you are familiar with chain saws, their proper usage, and the saw you purchased is fully assembled, use this Quick Start Guide to quickly begin using your new Remington brand chain saw. 10 Towards Guide Bar Nose Cutting Edge Guide Bar Chain Tensioning Screw Turn tensioning screw to move Adjustment Block LOCKED Guide Bar Retainer Rotated 90 Degrees to Guide Bar Slot Drive Sprocket Guide Bar UNLOCKED Guide Bar Retainer Positioned Parallel to Guide Bar Slot Drive Sprocket Guide Bar Note: Some models are pre-assembled. Assembly is not needed on these models. See Saw Chain Tension Adjustment 1. Lay chain out flat. 2. Loosen and remove guide bar nut and sprocket cover. 3. Rotate guide bar retainer so that it is positioned parallel to guide bar slot (see Figure 2). 4. Install guide bar onto saw body. Assemble center slot of guide bar onto guide bar bolt and guide bar retainer. Note: Make sure the head of the guide bar retainer slides through the guide bar slot as shown in Figure 2. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. IMPORTANT: Do not clamp chain saw in vise during assembly. Figure 3 - Locking Guide Bar Retainer 5. Rotate guide bar retainer 90 degrees as shown in Figure 3. Figure 2 - Unlocking Guide Bar Retainer ASSEMBLY Figure 5 - Chain Tensioning Screw and Adjustment Block Location 7. Before installing sprocket cover to saw body, turn the chain tensioning screw fully counterclockwise until it stops. This will position the adjusting block towards the end of the chain tensiong screw. (See Figure 5) Figure 4 - Saw Chain Direction 6. Place chain around drive sprocket, along top groove of guide bar, and around guide bar nose. Note: Make sure cutting edges of chain are facing in right direction. Position chain so cutting edges on top of guide bar face guide bar nose (see Figure 4 and indicator on side cover of saw). CAUTION: Do not place chain on saw backwards. If chain is backwards, saw will vibrate badly and will not cut. ASSEMBLY 8. Pull the guide bar away from the saw body so that the guide bar is fully extended and the slack is removed from the chain. (See Figure 6) Guide Bar Adjusting Hole Figure 6 - Pulling Guide Bar 9. Insert the sprocket cover tab into the saw body tab slot, Step 1. Then lower sprocket cover onto guide bar bolt, Step 2 (See Figure 7). NOTE: At this point the sprocket cover will not be flush against the saw body. Sprocket Cover Tab Tab Slot Sprocket Cover Tab Figure 7 - Installing Sprocket Cover 10. Finger tighten the guide bar nut onto the guide bar bolt. (See Figure 8). Guide Bar Nut Figure 8 - Guide Bar Bolt 11. Slowly slide guide bar into saw body until the adjustment block goes into the round adjusting hole on the guide bar. (See Figure 6) NOTE: This locks the guide bar in place. You should not be able to push or pull the guide bar. 12. Retighten the bar nut fi nger tight. 13. Adjust the saw chain tension. Follow the steps under Saw Chain Tension Adjustment.. ENGLISH 11 12 LOOSEN . Loosen nut... If chain becomes loose around guide bar, allow chain to cool then... . TIGHTEN TIGHTEN Turn chain tensioning screw clockwise to tension saw chain... . Pull chain to check tension. Guide links should not come out of guide bar groove... Tighten nut with wrench. A slight sag of 1/8" between chain and bottom of guide bar is acceptable. . . Guide Bar Approx. 5/32" WARNING: Unplug chain saw from power source before adjusting saw chain tension. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. WARNING: Maintain proper chain tension always. A loose chain will increase the risk of kickback. A loose chain may jump out of guide bar groove. This may injure operator and damage chain. A loose chain will cause chain, guide bar, and sprocket to wear rapidly. IMPORTANT! Failure to follow these instructions when tensioning saw chain will damage saw and void the warranty. For additional information call 1-800- 626-2237. New saw chains will stretch. Check chain tension frequently when fi rst used and tighten when chain becomes loose around guide bar. SAW CHAIN TENSION ADJUSTMENT OPERATING CHAIN SAW WARNING: Read and understand this owner’s manual before operating this saw. Make certain you read and understand all Important Safety Inform...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: