Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
. Children should be supervised to ensure that they do not play with the appliance. 7 Vibration The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by EN 60745 and may be used for comparing one tool with another. The declared vibration emission value may also be used in a preliminary assessment of exposure. Warning! The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used. The vibration level may increase above the level stated. . When assessing vibration exposure to determine safety measures required by 2002/44/EC to protect persons regularly using power tools in employment, an estimation of vibration exposure should consider, the actual conditions of use and the way the tool is used, including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time. Warning symbols The following warning symbols are found on your tool: Warning! To reduce the risk of injury, the user must read the instruction manual. Do not use your saw in wet conditions or expose it to rain. Always wear ear protection. Always wear eye protection. Always wear non-slip safety footwear. Beware of falling objects. Keep bystanders away. Do not use on ladders. To ensure continued safe operation, check the chain tension as described in this manual after every 10 minutes of use, and adjust back to a clearance of 3 mm as required. Oil the chain after every 10 minutes of use. Warning! Do not touch chain at the chip ejection point. Direction of rotation of the chain. To ensure continued safe operation, the chain and guide bar must only be replaced with original Black & Decker parts. Replacement chain part number A6158 replacement guide bar part number 90517720. Additional safety instructions for batteries and chargers Batteries . Never attempt to open for any reason. . Do not expose the battery to water. . Do not expose the battery to heat. . Do not store in locations where the temperature may exceed 40°C. . Charge only at ambient temperatures between 10°C and 40°C. . Charge only using the charger provided with the tool. . When disposing of batteries, follow the instructions given in the section “Protecting the environment”. . Do not damage/deform the battery pack either by puncture or impact, as this may create a risk of injury injury or fire. . Do not charge damaged batteries. Chargers Your charger has been designed for a specific voltage. Always check that the mains voltage corresponds to the voltage on the rating plate. . Use your Black & Decker charger only to charge the battery in the tool with which it was supplied. Other batteries could burst, causing personal injury and damage. . Never attempt to charge non-rechargeable batteries. . If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard. . Do not expose the charger to water. . Do not open the charger. . Do not probe the charger. Labels on the charger The following symbols are found on your charger: Your charging base is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. 8 The charging base is intended for indoor use only. Read the instruction manual before use. 130oC The charger automatically shuts off if the ambient temperature becomes too high. As soon as the ambient temperature has cooled down, the charger will resume operating. +40.C +10.C Charge only at ambient temperatures between 10°C and 40°C. Features 1. On/off switch 2. Lock-off button 3. Oil cap 4. Oil reservoir 5. Front guard assembly 6. Chain cover assembly 7. Chain tension adjustment screw 8. Chain 9. Guide bar 10. Battery 11. Chain sheath 12. Charger Assembly Warning! Before assembly, remove the battery (10) from the tool. Fitting and removing the battery (fig. A) . To fit the battery (10), line it up with the receptacle on the tool. Slide the battery (10) into the receptacle and push until the battery (10) snaps into place. . To remove the battery (10), push the release button (24) while at the same time pulling the battery (10) out of the receptacle. Warning! To prevent accidental operation, make sure that the battery is removed and that the chain sheath (11) is in place on the saw chain (8) before performing the following operations. Failure to do this could result in serious personal injury. Charging the battery (fig. B) Charging Warning! Do not charge the battery at ambient temperatures below 10°C or above 40°C. Recommended charging temperature is approximately 24°C. Note: The charger will not charge a battery pack if the cell temperature is below approximately 0°C or above 60°C. . Leave the battery pack in the charger and the charger will ...
Эта инструкция также подходит к моделям:Бензо и электропилы - Powerufl Solutions 90559283 (952.79 kb)