Войти:
Оценок - 4, средний балл: 3.5 ( )

Инструкция по эксплуатации Remington, модель 107714-02

Производитель: Remington
Размер: 1.12 mb
Название файла:
Язык инструкции:enesfr
Перейти к скачиванию



Фрагмент инструкции


WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. WARNING: Maintain proper chain tension always. A loose chain will increase the risk of kickback. A loose chain may jump out of guide bar groove. This may injure operator and damage chain. A loose chain will cause chain, guide bar, and sprocket to wear rapidly. Note: For pre-assembled models, the saw chain tension is properly set at factory. A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Follow steps below to readjust saw chain tension. 1. Before adjusting chain, make sure guide bar nuts are only finger tight (see Figure 3). Also make sure adjusting block is in oval adjusting hole on guide bar (see Figures 3 and 4). 108539 16 SAW CHAIN TENSION ADJUSTMENT Continued 2. Turn adjusting screw clockwise until all slack is out of chain (see Figure 5). Note: There should be no gap between side links of chain and bottom of guide bar (see Figure 6). 3. Wearing protective gloves, move chain around guide bar. Chain should move freely. If chain does not move freely, loosen chain by turning adjusting screw counterclockwise. 4. After chain tension is correct, tighten guide bar nuts firmly. If not, guide bar will move and loosen chain tension. This will increase the risk of kickback. This can also damage saw. Note: A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Readjust chain tension. FILLING OIL TANK 1. Remove oil cap. 2. Fill oil tank with SAE #30 motor oil. Note: For temperatures below 30°F, use SAE #10 oil. For temperatures above 75°F, use SAE #40 oil. 3. Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil seepage from tank. 4. Wipe off excess oil. Note: It is normal for oil to seep when saw is not in use. Empty oil tank after each use to prevent seepage. OPERATING CHAIN SAW WARNING: Read and understand this owner’s manual before operating this saw. Make certain you read and understand all Important Safety Information, pages 2 through 4. Improper use of this chain saw can cause severe injury or death from fire, electrical shock, or body contact with moving chain, or falling wood. EXTENSION CORDS Use proper extension cords with this saw. Use only extension cords marked for outdoor use. The cord must be marked with suffix W or W-A following the cord type designation. Example: SJTW-A or SJTW. Use proper sized cord with this saw. Cord must be heavy enough to carry current needed. An undersized cord will cause voltage drop at saw. Saw will lose power and overheat. Follow cord size requirements listed below. Cord Length AWG Cord Size 25 feet 16 AWG 50 feet 16 AWG 100 feet 16 AWG 150 feet 14 AWG Models LNT-2: 076728K, 100089-06, and 099178H; Pole Saw Assy: 104317 and 106821; Pole Saw: 104316-04 (8./20.3 cm) and 106890 (10./25.4 cm) Cord Length AWG Cord Size 25 feet 16 AWG 50 feet 16 AWG 100 feet 14 AWG 150 feet 12 AWG ...

Эта инструкция также подходит к моделям:
Бензо и электропилы - 075762J (1.12 mb)
Бензо и электропилы - 075762J (1.12 mb)
Бензо и электропилы - 098031J (1.12 mb)
Бензо и электропилы - 099039J (1.12 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории