Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Keep work area clean and well lit. 1. Cluttered or dark areas invite accidents. Keep children and bystanders away while operating a Chain Saw. 2. Distractions can cause you to lose control. Stay alert, watch what you are doing and use common sense when operating a 3. Chain Saw. Do not use this product while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating Chain Saws may result in serious personal injury. Use safety equipment. Always wear eye protection. 4. Safety equipment such as dust mask, non-skid safety shoes, ANSI approved hard hat, full face shield, and work gloves should be used for appropriate conditions to reduce personal injuries. Page 2 SKU 97092 For technical questions, please call 1-800-444-3353. Do not overreach. Keep proper footing and balance at all times. Do not use this 5. product on a ladder. This enables better control of the Chain Saw in unexpected situations. Store idle Chain Saws out of the reach of children and do not allow per6. sons unfamiliar with the tool or these instructions to operate it. Keep cutting tools sharp and clean. 7. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Always stand to one side and cut at a 45° angle to avoid falling debris. Do not 8. cut directly overhead. Do not use near utility lines. Plan ahead and clear the area beneath branches 9. being cut to avoid property damage or injury. Only use the Chain Saw to cut tree limbs and roots that have a diameter 10. less than 3”. This product is not a toy. Keep it out of reach of children.11. The warnings, precautions, and instructions discussed in this instruction manual 12. cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Save these instructions. Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Shake both Extension Ropes (2) out and remove any tangles or knots. Straight1. en the Chain Saw (3) and ensure that there are no kinks in it. Throw the Extension Rope with the weight over the branch that needs to be cut. 2. Use the hooks to connect the Chain Saw to the end of the weighed rope. Hook 3. the other Extension Rope to the other end of the Chain Saw and pull the chain up so that it engages the branch. Position the Chain Saw as close to where the branch meets the tree as possible. 4. Move as far away from the cutting area as the Extension Ropes allows. Con5. nect the Handles (1) to the ends of the Extension Ropes. Longer ropes of the same gauge as the Extension Ropes can be attached to the Chain Saw so that higher limbs can be cut and/or the user can be a safe distance away from the limb being cut. Cut at a 45° angle by pulling the Extension Ropes alternately with each hand. 6. As the Chain is pulled it will automatically orient itself to cut the limb. Cutting the bottom of the branch first will prevent the limb from peeling excess 7. amounts of bark from the tree when the limb falls. Saw the limb in long, brisk strokes. Use the full length of the Chain Saw to cut 8. the limb. Do not change position while cutting as this can cause the Chain to bind. Stay clear of the cutting area for safety. To cut roots, clear away dirt and debris from around the root, loop the Chain 9. Saw under the root, connect the Handles, and pull back and forth until the root is sawed through. Cut the root at a 45° angle, repeat at the other side of the root to remove it completely. Caution. Do not put excess pressure on the Chain Saw during this process or, when the root is cut through, the Saw could fly back toward the operator, possibly causing personal injury. Removing branches or roots can be traumatic to the tree and can provide an 10. entry point for disease and pests. Seek advice from your local lawn and garden specialist concerning care for the tree after limb removal. Clean, then store the tool indoors out of children’s reach.11. Maintenance And Servicing Damaged equipment can fail, causing serious personal injury. Do not use damaged equipment. BEFORE EACH USE,1. inspect the general condition of the tool. Check for loose fittings, frayed ropes, cracked or broken parts and any other condition that may affect its safe operation. Have Chain Saw sharpened by a qualified service technician.2. After Use,3. clean external surfaces of the tool with clean, moist cloth. Apply light machine oil before storage. PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provi...