Оценок - 4, средний балл: 4 ( )

Производитель: Little Wonder Размер: 903.11 kb Название файла: Язык инструкции:

Use only Lubrico M3-3K9K grease (P/N 16-78A) in the gear housing. Lubrico M24M (P/N 16-78B) is to be used on the motor bearings. Lubrico is available through your local Little Wonder Dealer. 5. Before each use, inspect to be sure handles, safety devices and fasteners are secure and in place, and cord is not frayed. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard. A. LUBRICATION AND MAINTENANCE WARNING DANGER KEEP HANDS AWAY FROM THE BLADES WHILE SERVICING THE HEDGE TRIMMER. BE SURE TRIMMER IS SECURED, UNPLUGGED, AND BLADES ARE GUARDED WHILE MAKING ADJUSTMENTS The care and adjustment of the blades is very important to the efficient operation of the trimmer and especially to the long life of the motor. Make sure the trimmer is NOT plugged in. 1. Turn trimmer upside down. Place trimmer in vice, clamping on the sides of frame bar. Be careful! Blades are sharp! 2. Using a 7/16” wrench, loosen all blade locknuts and unscrew the large head screws by two turns. 3. Starting with the screw nearest the gear housing, tighten the screw until the blade guard of the Single Edged trimmer or the protective comb of the Double Edged trimmer can just be moved with finger pressure. (A .0015" (1 1/2 thou.) feeler gauge just slips under the blade guard or comb when properly adjusted.) Tighten the locknuts while holding the screw stationary in its correct adjusted position. Re-check to make sure the blade guard or comb can still be moved. 4. Repeat Step 3 on each screw in turn until all are correctly adjusted. NOTE: CORRECT BLADE ADJUSTMENT CAN ONLY BE ACHIEVED ON CLEAN, OILED BLADES. B. BLADE ADJUSTMENT 8 A. TROUBLE SHOOTING Problem 1. Blades don’t cut cleanly. 2. Blades don’t move when turned on. 3. Excessive electrical arcing from vents in top of trimmer. Remedy Have blades sharpened and adjusted. Re-adjust blades following service instructions. Replace brushes - follow service instructions. Cause Blades are dull or not adjusted properly. Blades are adjusted too tight. Worn brushes. VI. SERVICE ! ! SINGLE EDGED DOUBLE EDGED Single Edge Assembly 9 KEY # PART # DESCRIPTION QTY. 1 310100 1 2 16-54B 7 2 16-54B 6 2 16-54B 5 3 310106 1 4 NA 1 5 310310 1 5 310305 1 5 310300 1 6 30-2 1 6 24-2 1 6 19-2 1 7 30-1 1 7 24-1 1 7 19-1 1 8 310215 1 9 16-93 5 9 16-93 4 9 16-93 3 10 16-54A 4 10 16-54A 3 10 16-54A 2 11 3036-B 3 12 310505 1 Gear Housing Assembly (including pressed in pins) Nut Lock 1/4-28 whiz Flange (for models 3010, 3012) 30” SE Nut Lock 1/4-28 whiz Flange (for models 2410, 2412) 24” SE Nut Lock 1/4-28 whiz Flange (for models 1910, 1912) 19” SE Frame Bar Support Side Handle Assembly (See individual part numbers) Frame Bar assembly (for models 3010, 3012) 30” SE Frame Bar assembly (for models 2410, 2412) 24” SE Frame Bar assembly (for models 1910, 1912) 19” SE Inside Blade (for models 3010, 3012) 30” SE Inside Blade (for models 2410, 2412) 24” SE Inside Blade (for models ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: