Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
18.3 Install front handle. A Roll front handle into place. B Install front handle screws (4). C Use blue Loctite® . D Torque to 69 in-lbs. (8 Nm). © 2007 ICS, Blount Inc. F/N 71537 Oct 07 TITLE 19. FUEL TANK TITLE 19. FUEL TANK 613GC SERVICE MANUAL 19 This section covers the disassembly, inspection, and assembly of the vibration isolaters, fuel tank, and rear handle. 19.1 Remove vibration isolator screws and wave washers on clutch side of saw. 19.2 Remove vibration isolator screws and wave washers on flywheel side of saw. F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE 19. FUEL TANK TITLE 19. FUEL TANK 613GC SERVICE MANUAL 19.3 Separate crankcase and fuel tank. NOTE: Saws have a rubber water deflector connected to the 2 bottom vibration isolators on the clutch side (circled). 19.4 Remove vibration isolators from fuel tank (6) if necessary. 19.5 Assemble in reverse order. NOTE: During assembly be careful to avoid kinking the fuel line. © 2007 ICS, Blount Inc. F/N 71537 Oct 07 TITLE 20. CRANKCASE TITLE 20. CRANKCASE 613GC SERVICE MANUAL 20 This section covers the disassembly, inspection, and assembly of the crankcase seals and crankshaft bearings. 20.1 Remove outer crankshaft seal housing screws and wave washers. 20.2 Remove crankcase bolts. F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE 20. CRANKCASE TITLE 20. CRANKCASE 613GC SERVICE MANUAL 20.3 Heat the flywheel side crankcase with heat gun for 5 minutes, approximately 150° F (65.5° C). 20.4 Remove the flywheel side crankcase – tap crankshaft with plastic mallet. A Suspend above work surface. B Tap with mallet. NOTE: A nut should always be placed on a threaded shaft when pounding or pressing on it. 20.5 Remove the flywheel side crankcase seal with 1/2” (13 mm) socket. © 2007 ICS, Blount Inc. F/N 71537 Oct 07 TITLE 20. CRANKCASETITLE 20. CRANKCASE 613GC SERVICE MANUAL 20.6 Heat the clutch side crankcase with heat gun to 150° F (65.5° C). 20.7 Remove crankshaft from the clutch-side crankcase tap crankshaft with a plastic mallet. A Suspend above work surface. B Tap with plastic mallet. 20.8 Remove the bearing from the flywheel side of crankshaft. F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE 20. CRANKCASE TITLE 20. CRANKCASE 613GC SERVICE MANUAL 20.9 Remove the bearing, seal, and bushing from the clutch side of crankshaft. 20.10 Clean mating crankcase faces. 20.11 Heat crankcase halves to 150° F. 20.12 Install bearing into crankcase halves. 20.13 Tap with bearing driver and mallet. © 2007 ICS, Blount Inc. F/N 71537 Oct 07 TITLE 20. CRANKCASETITLE 20. CRANKCASE 613GC SERVICE MANUAL 20.14 Repeat with other half. 20.15 Install crankshaft into clutch side of case. 20.16 Place clutch side crank case seal on crankshaft. A Tap lightly with bearing driver and mallet. F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE 20. CRANKCASE TITLE 20. CRANKCASE 613GC SERVICE MANUAL 20.17 Coat crankcase gasket with ICS® 2-stroke engine oil. 20.18 Align crankcase gasket on flywheel side crankcase pins. 20.19 Place crankcase halves together and align crankcase pins. © 2007 ICS, Blount Inc. F/N 71537 Oct 07 TITLE 20. CRANKCASETITLE 20. CRANKCASE 613GC SERVICE MANUAL 20.20 Assemble crankcase halves – tap with bearing driver and mallet. 20.21 Install main crankcase bolts. A Use blue Loctite®. BTorque to 69 in-lbs. (8 Nm). NOTE: The 3 remaining crankcase bolts will be installed during the completion of the saw assembly. 20.22 Install flywheel side crankcase seal – tap with bearing driver and mallet. F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE 20. CRANKCASE TITLE 20. CRANKCASE 613GC SERVICE MANUAL 20.23 Trim crankcase gasket flush. © 2007 ICS, Blount Inc. F/N 71537 Oct 07 613GC SERVICE MANUAL TITLE 21. BAR STUDS & BAR PAD 21 This section covers the removal and installation of the bar studs and bar pad. NOTE: On saws with Serial #’s beginning 0482421700 and 071XXXXXXX, it is necessary to remove the bar mount pad cover plate first. 21.1 Remove bar studs. A Remove side cover. B Install side cover nuts, flange to flange and tighten together. C Attempt to remove the inside nut which should pull out the bar stud. D Repeat on second bar stud. 21.2 Remove bar pad. A Remove sealing o-ring. 21.3 Assemble in reverse order. F/N 71537 Oct 07 © 2007 ICS, Blount Inc. TITLE 22. CHAIN TENSIONER TITLE 22. CHAIN TENSIONER 613GC SERVICE MANUAL 22 This section covers the removal and installation of the chain tensioner. 22.1 Remove bar plate to expose the chain tensioner. NOTE: Saws with serial #’s lower than 0482421700 are not equipped with a bar mount pad cover plate. 22.2 Unscrew tensioner to remove. A Remove tensioner pin. B Remove tensioner screw keeper. 22.3 Assemble in reverse order. © 2007 ICS, Blount Inc. F/N 71537 Oct 07 613GC SERVICE MANUAL TITLE 23. CARBURETOR TUNING 23 This section covers carburetor tuning. Included in this section are basic settings, idle speed adjustment, and complete adjustment. The carburetor has been set at the factory for optimal performance and compliance to EPA Phase I em...
Эта инструкция также подходит к моделям:Бензо и электропилы - ICS 613GC (4.44 mb)
Бензо и электропилы - ICS 613GC (4.44 mb)