Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
3. Release the front handle and drop the end of the guide bar against the wooden surface. 4. The impact should lock the chain brake. IMPORTANT When checking the operation of the automatic chain brake, use a soft surface substance like wood to provide the impact so the chain is not damaged. WINTER OPERATION Use the air shutter to prevent carburetor trouble in winter. • Remove air cleaner cover. Pull the air shutter to cold position. NOTE For operation at normal temperature, return the air shutter to its original place. (5°C, 41°F) It causes over heating of the engine. 21 CS-600P CHAIN AND GUIDE BAR COMBINATION The following combinations are recommended for model CS-600P. Guide Bar Saw chain Length mm (in.) ECHO Part No. Pitch mm (in.) Type OREGON Links Double Guard Symmetrical 406 (16) 508 (20) 610 (24) 686 (27) 16D0PD3860 20D0PD3870 24D0PD3881 —————— 16D0PS3860 20D0PS3870 24D0PS3881 27D0PS3893 9.53 (3/8) 9.53 (3/8) 9.53 (3/8) 9.53 (3/8) 72LPX,72V 72LPX,72V 72LPX,72V 72LPX,72V 60 70 81 93 GUIDE BAR Replacement guide bars. The following guide bars may be considered to have equivalent kickback energy. • Sprocket nose guide bars of the same length and nose radius, same pitch and having the same number of teeth. • Hard nose guide bars of the same length and nose radius as a sprocket nose bar. SAW CHAIN CAUTION Do not use replacement saw chain unless it has been designated as meeting the ANSI B175.1 - 2000 kickback performance requirements. NOTE LOW KICKBACK SAW CHAIN meets the kickback performance requirements of ANSI B175.1-2000 (safety requirements for gasoline- powered chain saws). CS-600P 22 MAINTENANCE AND CARE Your ECHO chain saw is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your chain saw achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed ask your ECHO dealer for repairs. MAINTENANCE INTERVALS SKILL LEVELS Level 1 = Easy to do. Most required tools come with unit. Level 2 = Moderate difficulty. Some specialized tools may be required. ECHO offers REPOWER™ Maintenance Kits and Parts to make your maintenance job easier. Just below each task heading are listed the various part numbers required for that task. Ask your ECHO dealer for these parts. Component/system Maintenance procedure Air Filter Inspect/Clean/Replace 1 I/C* R* Automatic Oiler Inspect/Adjust 1 I Oil Filter Inspect/Clean/Replace 1 I I/C* Fuel System Inspect/Replace 1 I (1)* I (1)* Fuel Filter Inspect/Replace 1 I* I/R* Fuel Cap Gasket Inspect/Replace 1 I* R Guide Bar and Sprocket Nose Inspect/Clean/Lubricate 1 I/C* I Saw Chain Inspect/Sharpen/Replace/ Tensioning 2 I* Sprocket Inspect/Replace 2 I* Spark Plug Inspect/Clean/Replace 1 I/C/R* Cooling System Inspect/Clean 2 I/C Muffler Spark Arrestor Inspect/Clean/Replace 2 I/C/R* Cylinder Exhaust Port Inspect/Clean/Decarbon 2 I/C Recoil Starter Rope Inspect/Clean 1 I/C* Screws/Nuts/Bolts Inspect/Tighten/Replace 1 I* Every refuelRequiredSkill levelDaily orBefore use3 Months or90 HoursYearly or600 Hours Meintenance Procedure Letter Codes: I = Inspect C = Clean R = Replace Meintenance Procedure Notes: (1)= Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity. *= All recommendations to replace are based on the finding of damage or wear during inspection. IMPORTANT Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. 23 CS-600P Idle adjusting screw Idle adjusting screw High speed needle (H) Low speed needle (L) CARBURETOR ADJUSTMENT Every unit is run at the factory and the carburetor is set in compliance with Emission Regulations. In addition, the carburetor is equipped with “H” (High Speed) and “L” (Low Speed) needle adjustment limiters that prevent settings outside acceptable limits. 1. Before adjusting carburetor clean or replace air filter and muffler “Spark Arrestor Screen”. 2. Make sure the bar and chain are properly adjusted. 3. Start engine and run several minutes to bring to operating temperature. Flash choke twice during warm-up to clear any air from the fuel system. 4. Stop engine. Turn “H” speed needle counterclockwise (CCW) to stop. Turn “L” speed needle midway between full clockwise (CW) stop and CCW stop. 5. Idle Speed Adjustment: • Start engine, turn “Idle” speed adjustment screw CW until the saw chain begins to turn, then turn screw out CCW until the saw chain stops turning. Turn screw out, CCW, an additional 1/4 turn. WARNING Cutting attachment must not move when unit is idling. 6. Accelerate to full throttle for 2 - 3 seconds to clear any excess fuel in the engine, then return to idle. Accelerate engine to full throttle to check for smooth transition from idle to high speed. If eng...