Войти:
Оценок - 1, средний балл: 4 ( )

Инструкция по эксплуатации AquaPRO, модель PRO1100

Производитель: AquaPRO
Размер: 2.12 mb
Название файла:
Язык инструкции:enes
Перейти к скачиванию



Фрагмент инструкции


All units are equipped with an electrical wiring schematic inside the electrical panel. If this is missing, please contact the factory at 1-877278- 2797 to obtain one. All units are to be wired for 230 VAC, 1 phase. These units require a dedicated 50-amp breaker or time delay fuse. Pool Heater is to be installed in accordance with Article 680 of the National Electrical Code (NEC), NFPA 70, and within the requirements of all local codes having jurisdiction. Electronic Temp. Controls All Units Except PRO1100 Description • The control located on the front of your heat pump has a large three- character display for the water temperature, set points, and diagnostics (see figure 3 for front panel appearance). The three button keypad includes SET, UP arrow, and DOWN arrow buttons. LED indicators next to the display show if the heat pump is in the pool mode or in the spa mode and if the unit is running. Figure 3 - Front Panel Buttons Press the SET button to change between modes and use the up and down arrows to change the selected mode’s settings. Modes available are: POL - allows you to change the pool water temperature set point SPA - allows you to change the spa water temperature set point P-S - changes between pool and spa settings. LED’s on front panel will indicate current mode selected. F-C - display temperature in Fahrenheit or Celsius TCE UNITS ONLY: FIL - used to set system run time. H/C UNITS ONLY: H-C - change between heating and cooling mode. Water Temperature Set Point Temperature set point range is OFF, and 61°F to 95°F for POL mode. For SPA mode, set point range is OFF, and 61°F to 104°F. Pushing the UP arrow or DOWN arrow buttons will prompt the control to display the current set point. Continuing to press the UP or DOWN buttons will allow the set point values to scroll until the desired set point is reached. Once the new set point has been reached, stop pressing the UP or DOWN buttons. Once the unit toggles back to the current water temperature display, the set point is entered. The controls have a feature called “Set Point Memory Retention”. If the power is removed from the unit, it retains the last set point displayed. Connecting to a Remote System: All Units Except Pro1100 This Pool Heater is compatible with all known remote systems in the industry. The following models’ diagrams show how to connect all of the remote systems to the Electronic Temp. Controller. For 2 wire remotes 1. Bring up “POL” setting and arrow temperature down until pool setting reads “off”. 2. Bring up “SPA” setting and arrow temperature up until spa setting reads 104. 3. Set unit to the “POL” mode. 4. Connect remote system with 2 wires to the P/S terminal on control board (see specific model wiring diagram). For 3 wire remotes 1. Bring up “POL” setting and use arrows to select desired pool temperature. 2. Bring up “SPA” setting and use the arrows to select the desired spa temperature. 3. Set unit to the “POL” mode. 4. Connect the common and high (or spa) wires to the “P/S” terminals on control board (see specific model diagram). Low or pool wire does not get connected. Note: For heat/ cool units, the remote will not work in the cooling mode. Connecting to Remote Systems: PRO1100 This Pool Heater is compatible with 2wire remote systems only, and is not compatible with 3 wire remote systems. Figure 4 shows where to connect the remote systems to the Temperature Controller. Connection to AquaLink, Compool, Hayward, AquaLogic or any other 2 wire remote system with their own thermostat: • Remove gray jumper from terminals 1 and 2 on TB1. • Bring the two wires from the remote system to terminals 1 & 2 on Terminal Block 1 (TB1). • The Temperature Control knob must be turned clockwise (highest temp. setting) for the remote system to operate the Pool Heater properly. High Temperature Lock Out: All Units Except PRO1100 Your heat pump includes a special feature to “lock” the high temperature settings. This eliminates the need for a thermostat lock-box. This prevents unauthorized persons from adjusting the heat pump above these desired limits. To activate this feature, please call AquaPRO® Systems at 877-AQUA-SYS (877-278-2797) during business hours 8 AM to 5 PM EDT Monday through Friday and we will be glad to assist in setting up this feature. Phone: (877)-278-2797 3 Operating Instructions PRO1100 Manual Temperature Controls Description • The manual Temperature Control is designed to regulate pool and spa water temperature. • There are two indicator lights on the control panel to display the current status of the unit. • The thermostat knob may be adjusted to maintain the desired water temperature. Indicator Lights • There are two indicator lights on the front panel that display unit status. The GREEN light indicates that power to the unit is on. The RED light indicates that the unit is in heating mode. • The RED light may become illuminated prior to heater start up. The RED light will become lit when the thermo...

Эта инструкция также подходит к моделям:
Бассейны - PRO1300 (2.12 mb)
Бассейны - PRO1300 TCE (2.12 mb)
Бассейны - PRO1300h/c (2.12 mb)
Бассейны - PRO1300h/c TCE (2.12 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории