• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 55W RMS x 4 channels, plus 225W RMS x 1 channel, @ 4 ohms and .1% TH

EXT/INT Switch • If the source unit has a subwoofer output and you have connected it to the SUB input, set this switch to the EXT position. Otherwise, set it in the INT position. Subwoofer Remote Level Control Connector • Connect the Remote Level Control (RLC) here, using the supplied RJ-11 cable. Subwoofer Level Control • Used to match the SUB input of the amplifier to the output of the source unit. • See for adjustment procedures. Protect LED • Illuminated under any of the following fault cond

• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 425W RMS x 1 channel @ 4 ohms and .1% THD + N* • 700W RMS x 1 channe

• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 1700W RMS x 1 channel @ 4 ohms and .1% THD + N* • 2400W RMS x 1 chan

Either + or -terminal may be used. Minimum total impedance is 1 ohm. © Fuses • Replace only with the same type and rating. © Power Input Connectors • +12V: Connect to the positive terminal of the vehicle's battery. 8 AWG wire is recommended. Install an appropriate fuse holder and fuse (40A minimum) within 18 inches of the battery. Make sure the wire is not damaged or pinched during installation. Install protective grommets when routing wires through the firewall or other sheet metal. • GND:

Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 200W RMS x 1 @ 4 ohms and <1% THD + N* • 300W RMS x 1 @ 2 ohms, 14.4V supply and <1% THD + N* • Maximum input signal: 6V* • Maximum sensitivity: 200mV* • THD + N: 0.05%* • Signal-to-noise

• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 225W RMS x 1 channel @ 4 ohms and <1% THD + N* • 360W RMS x 1 channe

(SP) Configuración de los altavoces en la función de las entradas e instalada. RCAINPUT CH1/CH2 CH3/CH3 SWITCH INPUT 4CH 2CH SWITCH OUTPUT DUAL SPEAKER OUTPUT CONFIGURATION * * * * * * * 4or2 ohm 4or2ohm 4or2ohm * * * * * * * Speakersoutput m? CH1/CH2 Speakersoutput m? CH3/CH4 4or2 ohm 4ohmONLY * * * - : Speakersoutput 1 m? a CH1/CH2 0 : 1 J Speakersoutput -, + i m? o n CH3/CH4 o 1 J 4ohmONLY 4ohmONLY 06 J CH1/CH2 Speakers connection (

INSTALLATION 2 THANK YOU for purchasing a JBL CS Series amplifier. In order that we may better serve you should you require warranty service for your new amplifier, please retain your original purchase receipt and register your new JBL amplifier online at WARNING Playing loud music in an automobile can hinder your ability to hear traffic and permanently damage your hearing. We recommend listening at low or moderate levels while driving your car. JBL accepts no liability for hearing loss, bodily

Instead, please ask your authorized JBL car audio dealer about professional installation. INSTALLATION CHOOSING A LOCATION WARNINGS AND TIPS AND MOUNTING THE • Always wear protective eyewear when using tools. • Turn off the audio system and other electrical devices before you start. Disconnect the (–) negative lead from your vehicle’s battery. • At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when