Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
Enables the matching of input levels to the output levels from head unit (or other signal source). The input sensitivity of adjustment ranges from 6V to 200mV. crossover frequency control When crossover mode selector is in HIGHPASS mode, this control sets the lower frequency limit for audio program sent to the speakers. When crossover mode selector is in LOWPASS mode, this control sets the upper frequency limit for audio program sent to the speakers. bass boost level selector bass boost level control The crossover is continuously variable adjustment from 40 t0 250 Hz. This selector switch permits the bass level an increase of 18dB. This control permits adjustment of the bass level up to an increase of sub sonic control approximately up to 18dB. When the sub sonic selector switch is in "ON" mode, this filter control permits continuously variable adjustment from 10 to 100Hz. low level input This amp features gold-plated RCA type jacks for high impedance input. Use these with car stereo output which uses RCA type connector cables. high level input If your car stereo jacks RCA type output, use this adaptor to connect the high-low level input adaptor to connect the speaker output leads of car AUX line outputs power LED protection LED stereo and the RCA input jacks of amp. This amp features gold-plated RCA jacks for AUX line outputs. Use these outputs. Use these for unlimited system expansion to the next CHOPPER. This indicator is illuminated in GREEN when power is applied. This indicator is illuminated in RED when the built-in protection circuitry is actirated. power fuse The fuse protects the amplifier and your car's electrical system from short circuit conditions. power terminals Use these connectors to deliver power, ground, and remote turn-on control speaker connectors to the amplifier. These terminals are 14K gold plated to guarantee high conductivity and minimum signal loss. RMS Power @ 4 Ohms THD @ 4 Ohms RMS Power @ 2 Ohms THD @ 2 Ohms Maximum Power Output bridged Power at 4 Output PLA-2230 200 Watts x 2 00 Watts x 2 00 Watts x 2 00 Watts x 2 1500 Watts x 2 3000 Watts x 1 frequency response 15 Hz-30 KHz input impedance low level inputs 10K Ohms input sensitivity low level inputs 250mV S/N ration >95dB channel separation >65dB crossover filters low Pass 40 Hz-250 Hz high Pass 40 Hz-250 Hz bass boost 0~ +18dB PLA-2260 PLA-2260 300 Watts x 2 00 Watts x 2 00 Watts x 2 00 Watts x 2 2000 Watts x 2 4000 Watts x 1 6 matching speaker impedance stereo mode bridged mode maximum current draw power supply voltage dimensions (W x H x L) mm inches 2-4 Ohms 4-8 Ohms 00Ax2 00Ax2 14.4V DC Neg. Ground (10.5-16V) 270 x 36 x 432 270 x 36 x 532 10.63 x 1.42 x 17 10.63 x 1.42 x 21 features and controls 2 ch amp PLA-2230 • PLA-2260 PLA-2230 PLA-2260 7 features and specifications crossover mode selector input level controls crossover frequency control bass boost level selector bass boost level control sub sonic control low level input high level input AUX line outputs power LED protection LED power fuse power terminals speaker connectors When used with normal, full range system, set this switch to "FULL" . If you wish to use the internal crossover to power a driver or specific frequency range, use the "LPF"or "HPF" FOR the "LOWPASS" OR HIGHPASS" settings. Enables the matching of input levels to the output levels from head unit (or other signal source). The input sensitivity of adjustment ranges from 6V to 200mV. When crossover mode selector is in HIGHPASS mode, this control sets the lower frequency limit for audio program sent to the speakers. When crossover mode selector is in LOWPASS mode, this control sets the upper frequency limit for audio program sent to the speakers. The crossover is continuously variable adjustment from 40 t0 250 Hz. This selector switch permits the bass level an increase of 18dB. This control permits adjustment of the bass level up to an increase of approximately up to 18dB. When the sub sonic selector switch is in "ON" mode, this filter control permits continuously variable adjustment from 10 to 100Hz. This amp features gold-plated RCA type jacks for high impedance input. Use these with car stereo output which uses RCA type connector cables. If your car stereo jacks RCA type output, use this adaptor to connect the high-low level input adaptor to connect the speaker output leads of car stereo and the RCA input jacks of amp. This amp features gold-plated RCA jacks for AUX line outputs. Use these outputs. Use these for unlimited system expansion to the next CHOPPER. This indicator is illuminated in GREEN when power is applied. This indicator is illuminated in RED when the built-in protection circuitry is actirated. The fuse protects the amplifier and your car's electrical system from short circuit conditions. Use these connectors to deliver power, ground, and remote turn-on control to the amplifier. These terminals are 14K gold plated to guarantee high conductivity and minimum signal loss. output power @ ...
Эта инструкция также подходит к моделям:Автоусилители - PYLE Chopper Series PLA-2260 (428.7 kb)
Автоусилители - PYLE Chopper Series PLA-4120 (428.7 kb)
Автоусилители - PYLE Chopper Series PLA-2260 (428.7 kb)