Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
N o X o v e r point. HIGH LEVEL INPUT: Speaker level inputs with a range of 0.5V to 17V RMS. Specifications Are Subject To Change Without Notice TD5X This information applies to SUB INPUT: This is your s u b w o o f e r channel where the sub RCA outputs from your head unit are inserted. INPUT SELECTOR: This tells the amp to play all channels even if only one pair of RCAs is connected. EXAMPLE: If the head unit only has one pair of RCA outputs then you must plug them into the CH1/2 connections and set the switch to 2. This tells the amp that you are using one set of RCAs and it needs to play all five channels regardless. If you have four RCAs, then set it to 4 and so on. SUB XOVER: The Xover provides control over the device cutoff frequency. 0-18dB/Oct REMOTE SUB LEVEL: Allows you to adjust bass output i n t e n s i t y remotely. amps LOW INPUTS: These are CH1/2(FRONT) & 3/4(REAR) low inputs with a range of 0.2V to 7V RMS. This is where the front and rear RCA outputs from your head unit are inserted. R L L R R LGAIN HP LPFR XOVER GAIN XOVER 5 4 2 AUTO ON REMOTE ONRESET CHANNEL 1/2 SIGNAL FLOW CHANNEL 3/4 SIGNAL FLOW MONO CHANNEL 5 SIGNAL FLOW 40MIN MAX 160 REMOTE SUBWOOFER CONTROL CHANNEL 1/2 CONTROL CHANNEL 3/4 CONTROL INPUT SELECTOR HP LPFR40MIN MAX 400 GAIN XOVER 40MIN MAX 400 2 1 4 3 MODE MODE MODE SELECTOR: This feature tells the amplifier to run in either HIGH PASS, FULL RANGE or LOW PASS MODE LEVEL ADJUST: Control the max output of each channel. The LEVEL controls its respective channel regardless how many inputs in use. VARIABLE XOVER: C o n t r o l t h e corresponding channels' cutoff frequencies. This feature is disabled when in FULLRANGE. both channels 1/2 and 3/4 LEVELADJUST: Allows the amplifier to deliver a controlled maximum sound level into selected channel(s) when the volume is turned to max. This acts as a volume l imit e r fo r the sy stem, preventing you from over driving the speakers or subwoofers. AUTO SIGNAL SENSING: Please refer to p a g e 3 f o r explanation of this feature. SUB XOVER SETTING TD5X 40Hz 100Hz 180Hz 280Hz 360Hz 400Hz 7.0V 4.0V 2.5V 1V MAX INPUT VOLTAGE BEFORE CLIPPING The gain knob is not a volume control. It is designed to match the input level of the amp to the output level of the source unit. Over driving "clipping" the input stage of the amp will cause damage to the amplifier (please refer to table for setting). RCA LEVEL 14 To car chassis / ground To remote turn on / trigger To battery positive (+) Three 25A fuses Bridgeable speaker outputs, minimum 4-Ohms, plus subwoofer connection. FUSESGND REMOTE POWER OUTPUT +12V CH2+ CH2CH2CH4FRONT BRIDGED BRIDGED CH1CH1+ CH1+ CH3+ SUB - + CH4+ CH4REAR CH3CH3+ 25A 25A 25A PROT PWR POWER (PWR) LED: When LED is on, it indicates that the amplifier is ON and functioning properly. PROTECTION (PROT) LED: If LED comes on then you have an issue that requires service. Turn off the amplifier and call Earthquake for further assistance. See warranty for details. Specifications Are Subject To Change Without Notice OUTPUT CH2+ CH2CH2+ CH5CH2CH5+ CH2CH4FRONT BRIDGED BRIDGED CH1CH1+ CH1CH1+ CH1+ CH3+ SUB - + CH4+ CH4REAR CH3CH3+ FC6.2 Mid-Range FC6.2 XoverFC6.2 Xover FC6.2 Tweeter FC6.2 Tweeter FC6.2 Mid-Range Focus EQ-693 Focus EQ-693 The Sub Channel Will Accept 2 or 4-Ohm Subwoofers CH3/4 FULL LOWHIGH MIN MAX LEVEL 400Hz40Hz XOVER Set Xover switch to FULL (full range) Set Xover to desired setting and set Mode switch to HIGH (high-pass). Level adjustment should be dialed in by ear. Keep it at MIN and slowly work your way up. CH1/2 FULL LOWHIGH MIN MAX LEVEL 400Hz40Hz XOVER ...
Эта инструкция также подходит к моделям:Автоусилители - T1000W/2 (1.05 mb)
Автоусилители - T2000W/4 (1.05 mb)
Автоусилители - T2000WD/1 (1.05 mb)
Автоусилители - T500W/2 (1.05 mb)