Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
use this control to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o’clock position, increase the amp level control until distortion begins to occur, and reduce slightly from this point. when the crossover selector switch is in “low pass” mode, this control sets the upper frequency limit for audio program sent to the speakers. when the crossover selector switch is in “high pass” mode, this control sets the lower frequency limit for audio program sent to the speakers. this control permits adjustment of the bass level up to an increase of approximately 18 dB. this amp features gold-plated RCA input jacks for high impedance input. Use these with car stereo output which uses RCA-type connector cables. if your car stereo lacks RCA-type output jacks, you may connect speaker output leads to these input connectors. this indicator is illuminated when power is applied. this indicator is illuminated when built-in protection circuitry is activated. the fuse protects the amplifier and your car’s electrical system from short circuit conditions. use these connectors to deliver power, ground and remote turn-on control to the amplifier. these terminals are 14K gold plated to guarantee high conductivity and minimum signal loss. output power @ 14.4v DC, 1KHz RMS Power @ 4 Ohms 40 Watts x 2 RMS Power @ 2 Ohms 60 Watts x 2 Maximum Power Output 300 Watts x 2 frequency response 15 Hz-30 KHz input impedance low level inputs 10K Ohms high level inputs 100 Ohms input sensitivity low level inputs 250mV high level inputs 2.5V power supply voltage 14.4V DC Neg. Ground (10.5-16V) matching speaker impedance stereo mode 2-4 Ohms bridged mode 4-8 Ohms maximum current draw 15A dimensions (W x H x L) mm 276 x 60 x 209 inches 10.9 x 2.4 x 8.25 5 high level inputs input level control crossover mode selector protection LED low pass frequency control bass boost level low level inputs power LED high pass frequency control speaker connections power terminals power fuse 6 pb781X features and controls 2 ch amp P B781X features and specificationfeatures and specifications 2 ch amp PB781X crossover mode selector input level control low pass frequency control high pass frequency control bass boost level control low level inputs high level inputs power LED protection LED power fuse power terminals speaker connections when used with normal, full range systems, set this switch to “FULL.” If you wish to use the internal crossover to power a driver of specific frequency range, use the “LOWPASS” or “HIGHPASS” settings. use this control to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o’clock position, increase the amp level control until distortion begins to occur, and reduce slightly from this point. when the crossover selector switch is in “low pass” mode, this control sets the upper frequency limit for audio program sent to the speakers. when the crossover selector switch is in “high pass” mode, this control sets the lower frequency limit for audio program sent to the speakers. this control permits adjustment of the bass level up to an increase of approximately 18 dB. this amp features gold-plated RCA input jacks for high impedance input. Use these with car stereo output which uses RCA-type connector cables. if your car stereo lacks RCA-type output jacks, you may connect speaker output leads to these input connectors. this indicator is illuminated when power is applied. this indicator is illuminated when built-in protection circuitry is activated. the fuse protects the amplifier and your car’s electrical system from short circuit conditions. use these connectors to deliver power, ground and remote turn-on control to the amplifier. these terminals are 14K gold plated to guarantee high conductivity and minimum signal loss. output power @ 14.4v DC, 1KHz RMS Power @ 4 Ohms 50 Watts x 2 RMS Power @ 2 Ohms 75 Watts x 2 Maximum Power Output 500 Watts x 2 frequency response 15 Hz-30 KHz input impedance low level inputs10K Ohms high level inputs 100 Ohms input sensitivity low level inputs250mV high level inputs 2.5V power supply voltage 14.4V DC Neg. Ground (10.5-16V) matching speaker impedance stereo mode 2-4 Ohms bridged mode 4-8 Ohms maximum current draw 15A dimensions (W x H x L) mm 276 x 60 x 279 inches 10.9 x 2.4 x 11 7 speaker connections power terminals power fuse Remote Bass Boost 8 pb1281X features and controls 2 ch amp PB 1 2 8 1 X high level inputs input level control crossover mode selector protection LED low pass frequency control bass boost level low level inputs power LED high pass frequency control 2 ch amp PB 1 2 8 1 X 9 crossover mode selector input level control low pass frequency control high pass frequency control Remote Bass Boos...
Эта инструкция также подходит к моделям:Автоусилители - PB881X (889.71 kb)
Автоусилители - PB1881X (889.71 kb)
Автоусилители - PB481X (889.71 kb)
Автоусилители - PB681X (889.71 kb)