Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Remove/Install Four Allen-head screws hold the control panel cover to the amplifier top panel, one at each corner. They can be removed with the wrench supplied in the hardware pack. © 2002 Directed Electronics, Inc SPEAKER WIRING DIAGRAMS Single subwoofer connection (top view) Two subwoofer connection (top view) N NNO OOT TTE EE: :: The dual + and -- subout terminals of the 600d/1100d are paralleled internally and the combined load impedance should be taken into consideration when connecting multiple subwoofers. © 2002 Directed Electronics, Inc COMBINING AMPLIFIERS The Viper 600d/1100d subwoofer amplifiers have the capability of connecting two or more amplifiers of the same power rating together in a master/slave combination for increased power with accurate level matching. They are the Parallel Synced Gain and External Synced Bridged combinations. W WWA AAR RRN NNI IIN NNG GG: ::DO NOT attempt to combine amplifiers of different power ratings. These amplifier combinations work correctly only if the Master and Slave amplifiers are identical models. Parallel Synced Gain In this master/slave combination the master amplifier pre-amp controls remain active and the slave amplifier pre-amp is bypassed. This allows the master amplifier to control gain, filter, and sub-level on both amplifiers. This combination allows the amplifiers to drive their own separate subwoofer(s) while being synced together via an in- phase audio pre-amp signal from the master amplifier. Wiring connections to the amplifier subwoofer outputs in this combination should be standard in-phase configurations, creating a parallel speaker connection. (Refer to Parallel Synced Gain section of this guide for amplifier and speaker connection diagrams.) N NNO OOT TTE EE: ::One master amplifier can control up to three slave amplifiers in this combination. Multiple identical master/slave combinations can be added to any given system. External Synced Bridged In this master/slave combination the master amplifier pre-amp controls remain active and the slave amplifier pre-amp is bypassed. This allows the master amplifier to control gain, filter, and sub-level on both amplifiers. This combination allows the amplifiers to drive common subwoofer loads while being synced together via an out-of-phase audio pre-amp signal from the master amplifier. In this subwoofer wiring configuration the master amplifier sends the positive signal to the subwoofer while the slave amplifier sends the negative signal, making an externally bridged speaker connection. (Refer to External Synced Bridged section of this guide for amplifier and speaker connection diagrams.) N NNO OOT TTE EE: ::Amplifiers in this combination can only be connected in matched pairs. Multiple matched pairs may be added to drive separate subwoofer loads in a given system. Combined Amplifiers Gain and Filter Settings Set the Subsonic, EQ, and other filter settings on the master amplifier to the positions that achieve the best sound quality. Adjustment guidelines are discussed in the Crossover and Gain Adjustmentsection of this guide. © 2002 Directed Electronics, Inc PARALLEL SYNCED GAIN CONNECTIONS/SETTINGS 1. I IIn nnp ppu uut tt S SSi iig ggn nna aal ll - Connect these RCA jacks as described in the Front Panel Connectionsection of this guide. 2. S SSl lla aav vve ee/ //M MMa aas sst tte eer rr S SSw wwi iit ttc cch hh • Set the slave/master switch on the master amplifier to the MASTER position. • Set the slave/master switch on the slave amplifier to the SLAVE position. • Setting the slave/master switch on both amplifiers will automatically set the I/O RCA jack configuration according to each amplifier’s slave or master designation. N NNO OOT TTE EE: ::One master amplifier can control up to three slave amplifiers in this combination. Multiple identical master/slave combinations can be added to any given system. 3. R RRe eem mmo oot tte ee S SSu uub bb L LLe eev vve eel ll C CCo oon nnt ttr rro ool ll - Connect the Remote Sub Level Control to the master amplifier only. The master amplifiers subwoofer gain is used to set the overall gain for all synced amplifiers, then the Remote Sub Level Control can adjust the gain of all synced amplifiers. 4. S SSi iig ggn nna aal ll C CCo oon nnn nne eec cct tti iio oon nn - Connect an RCA cable between the SYNC OUT RCA jack of the master amplifier and the SLAVE IN RCA jack of the slave amplifier as shown in the Figure 5. 5. S SSu uub bbw wwo ooo oof ffe eer rr S SSp ppe eea aak kke eer rr C CCo oon nnn nne eec cct tti iio oon nn - In this amplifier combination each amplifiers must drive its own separate subwoofer(s). Connect the speaker terminals of each amplifier to any combination of one or more subwoofers that results in nominal impedance between one and four ohms. Make sure that each amplifier sees the same speaker impedance. © 2002 Directed Electronics, Inc FIGURE 5—PARALLEL SYNC GAINED 600d/1100d Master 12 3 Slave 4 Do Not Use Do Not Use ...
Эта инструкция также подходит к моделям:Автоусилители - 1100d (474.34 kb)