Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
If unavailable, use the high level inputs - when interfacing with factory head unit for instance. CAUTION • Do not use both low and high level inputs at the same time - connect only one or the other. 4 XIA5600 INSTALLATION Connections and Controls Low Level Inputs High Level Inputs Input Level Control Crossover Frequency Crossover Mode Switch Bass Boost LED Indicator 1 2 3 Ground Connection Remote Connection +12VDC Battery Connection Main Fuses illuminite Fuse illuminite Outputs Speaker Connections 1 2 3 4 5 6 7 4 5 6 7 8 9 10 11 12 13 14 14 13 12 11 10 9 8 XIA5600 INSTALLATION Typical Wire Routing Main Power Connections Connect +12V, GND and REM wires accordingly. A suitable fuse MUST be installed on the +12V lead within 18" of the battery for protection of the vehicle’s electrical system. Fuse Rating When replacing fuses, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the amplifier. Main fuse 30 amp ATO x 3 illuminite fuse 2 amp ATO x 1 Power/Ground Wire Size For optimum performance, use only the wire size listed below or larger. Make sure to use the same size power and ground wire. Power/ground 4 gauge illuminite output 18 gauge XIA5600 INSTALLATION Output Connections The lighting elements of DUAL illuminite speakers provide you with a unique custom touch to your vehicle. Dual’s patent pending illuminite LED system and control circuitry provides an extraordinary blue-hue illumination which allows great creative opportunities for the beginner and seasoned custom installer alike. DUAL XIA-series amplifiers provide a dedicated switched 12VDC output including independent fused protection (2 amp) specifically for use with illuminite speakers. DUAL illuminite speakers have two distinct sets of input terminals. The first is labeled audio input terminals and the second is labeled illuminite lighting inputs. The inputs are clearly marked with a label positioned directly above the terminal housing. The polarity (+ and -) indicators for each set of inputs also appear on these labels. 1. Do not connect the amplifier speaker outputs or any audio source to the illuminite lighting inputs. 2. Refer to the figures below for making the connections. Make sure to observe polarity as the illuminite circuitry will not operate when connected reverse polarity. Connect either red wire from the XIA amplifier illuminite outputs to the positive (+) illuminite input terminal and connect either black wire from the XIA amplifier illuminite outputs to the negative (-) illuminite input. Additional illuminite wiring notes: Several illuminite speakers can be connected to the 12VDC illuminite output at one time. Refer to the table below for the individual illuminite speaker current requirements. If you are unsure, consult a qualified professional or call DUAL technical assistance at 1-866-382-5476 for further information. OUTPUT CONNECTOR (Plugs into amplifier) XiNC112 - 55mA XiNC110 - 55mA XiNBP210 - 180mA XiNBP212 - 180mA XOBP12D - 130mA illuminitecurrentrequirements(perspeaker) 7 XIA5600 INSTALLATION Amplifier Connections Speaker Connections Connect speaker wires observing polarity. The minimum impedance load is 2 ohms stereo and 4 ohms bridged. Use of loads lower than these is not recommended and may cause amplifier damage. The XIA5600 can be wired for stereo, bridged or stereo/bridged simultaneous operation. Input Signal Connections Low Level Input (RCA) Low level (RCA) input signal is preferred for best performance. Typical trunk-mount amplifier installations require a 17-20 foot RCA cable. Most trucks and under-seat applications require a 6-9 foot RCA cable. Using twisted pair construction RCA cables will minimize noise. High Level Input (Speaker Wire) High level inputs should only be used when RCA outputs are not available from the head unit. Connect the head unit speaker outputs to the high level input connector as shown below. The black wire (signal reference ground) may or may not require a connection to chassis ground - depending on your particular installation. CAUTION: Do not use both low and high level inputs at the same time - connect only one or the other. Subwoofer (mono) Typical Bridged Wiring (4 ohms minimum) 2 Speakers (stereo) Typical Stereo Wiring (2 ohms minimum) XIA5600 OPERATION Configuration/Setup Input level Control The input level control (gain) is used to obtain the best possible match between the head unit audio output and the amplifier input. Begin by turning the input level control fully counterclockwise. Next, turn up the head unit volume control around 3/4 of the way up. Adjust the input level control clockwise until audible distortion is heard, then slightly counterclockwise to provide the best match. Crossover Mode The crossover is used to filter out frequencies above or below a certain point. Choose LPF when using the amplifier with subwoofers and FULL when using with coaxial-type speakers. NOTE: Choose FULL when using the amplifier in stereo/bridged simultane...